Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
14 | English
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it un-
stable and may lead to loss of control.
Keep hands away from the sawing area. Do not reach
u
under the workpiece. Contact with the saw blade can
lead to injuries.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Ensure that the footplate always rests securely while
u
sawing. A jammed saw blade can break or lead to kick-
back.
When the cut is completed, switch off the power tool
u
and then pull the saw blade out of the cut only after it
has come to a standstill. In this manner you can avoid
kickback and can place down the power tool securely.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Use only undamaged saw blades that are in perfect
u
condition. Bent or dull saw blades can break, negatively
influence the cut, or lead to kickback.
Do not brake the saw blade to a stop by applying side
u
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
1 609 92A 51A | (09.04.2019)
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for making separating cuts and
cut-outs in wood, plastic, metal, ceramic plates and rubber
while resting firmly on the workpiece. It is suitable for
straight and curved cuts with mitre/bevel angles of up to
45°. Note the saw blade recommendations.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch locking mechanism
(2) On/off switch
A)
(3) Dust extraction hose
(4) Extraction outlet
(5) Saw blade storage compartment (PST 800 PEL/
PST 8000 PEL/PST 8500 PEL)
(6) Base plate
(7) Pendulum action adjusting lever
(8) Sawdust blower device switch
(9) Hood for dust extraction (PST 800 PEL/
PST 8000 PEL/PST 8500 PEL)
(10) Base for Cut Control (PST 800 PEL/PST 8000 PEL/
PST 8500 PEL)
(11) Viewing window for Cut Control (PST 800 PEL/
PST 8000 PEL/PST 8500 PEL)
(12) Handle (insulated gripping surface)
(13) Saw blade receptacle
(14) Guide Roller
A)
(15) Saw blade
A)
(16) Anti-splinter guard
(17) Accessory Holder
(18) Shock protection guard
(19) Base plate screw
(20) Scale for mitre/bevel angles
(21) Cut mark 0° (PST 800 PEL/PST 8000 PEL/
PST 8500 PEL)
(22) Cut mark 45° (PST 800 PEL/PST 8000 PEL/
PST 8500 PEL)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Bosch Power Tools
Advertenties
Inhoudsopgave
