Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Refined Salt and Rinse Aid
Only use products which have been specifically designed
for dishwashers. Do not use table salt or industrial salt.
Follow the instructions given on the packaging.
If you are using a multi-function product, we recommend
that you add salt in any case, especially if the water is hard or
very hard. (Follow the instructions given on the packaging.)
If you do not add salt or rinse aid, the LOW SALT
*
LOW RINSE AID
indicator lights will remain lit.
Measuring out the refined salt
The use of salt prevents the formation of LIMESCALE on the dishes
and on the machine's functional components.
• It is important that the salt dispenser be never empty.
• It is important to set the water hardness.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
• When the LOW RINSE AID indicator light in the control panel
*
is lit
;
*
• When the green float
on the cap of the salt dispenser is no
longer visible.
• See autonomy in the water hardness table.
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. Only the first time you do this: fill the water
dispenser up to the edge.
3. Position the funnel
fill the salt container right up to its edge
(approximately 1 kg); it is not unusual for a
little water to leak out.
4. Remove the funnel and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it on.
It is advisable to perform this procedure every time you add salt
to the container.
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whenever you need to add salt, we recommend carrying out
the procedure before the washing cycle is started.
Setting the water hardness
For perfect water softener operation, it is essential that the
adjustment be based on the water hardness in your house. Ask
your local water supplier for this information. The factory setting
is for medium water hardness.
• Switch the dishwasher on using the On/Off button.
• Switch it off using the On/Off button
• Hold down button P for 5 seconds until you hear a beep.
• Switch it on using the On/Off button
• The current selection level number and salt indicator light flash
(flashing indicator only).
• Press button P to select the desired hardness level (see
hardness table).
• Switch it off using the On/Off button
• Setting is complete!
Even if using multi-functional tablets, the salt dispenser should
still be filled.
*
Only available in selected models.
Water Hardness Table
level
1
2
3
*
and
*
4
For values between 0°f and 10°f, we do not recommend the use
of salt. * this setting may cause a slight increase in the duration
of the cycles.
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees – mmol/l = millimoles per litre)
Measuring out the rinse aid
Rinse aid makes dish DRYING easier. The rinse aid dispenser
should be filled:
• When the LOW RINSE AID indicator light on the panel/display
*
is lit
• When the dark optical indicator
becomes transparent.
(see figure)
and
1. Open the dispenser
on the lid;
2. Carefully introduce the rinse aid as far as the maximum reference
notch of the filling space - avoid spilling it. If this happens, clean
the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Rinse-aid dispenser setting
If you are not completely satisfied with the drying results, you
can adjust the quantity of rinse aid used.
• Switch the dishwasher on using the On/Off button.
• Switch it off using the On/Off button
• Press button P three times - a beep will be heard.
• Switch it on using the On/Off button
• The current selection level number and rinse aid indicator light
flash (flashing indicator only).
• Press button P to select the level of rinse aid quantity to be
supplied.
• Switch it off using the On/Off button
• Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid.
A maximum of 4 levels can be set according to the dishwasher
model. The factory setting is for a medium level.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
Average autonomy
salt dispenser with 1
wash cycle per day
°dH
°fH
mmol/l
0 - 11
0 - 20
1,1 - 2
12 - 17
21 - 30
2,1 - 3
17 - 34
31 - 60
3,1 - 6
34 - 50
61 - 90
6,1 - 9
;
*
on the dispenser door "D"
"D"
by pressing and pulling up the tab
EN
months
5 months
3 months
2 months
2/3 weeks
27
Advertenties
Inhoudsopgave
