Advertenties
Beschikbare talen
Beschikbare talen
ELA Coaxial Speaker
Item no. 31 20 60
CL-100RCV
Item no. 31 20 59
CL-130RCV
Item no. 31 21 19
CL-165RCV
1.
Intended use
The built-in loudspeaker with plastic rear enclosure is intended for converting the electric output signals from audio amplifiers into
audible sound waves and is only approved for connection to the loudspeaker outputs of such devices.
May only be used indoors; never outdoors. Do not expose to moisture, for example in bathrooms or similar spaces.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product for purposes other
than those described above, the product may be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
2.
Delivery content
•
ELA Coaxial Speaker
•
Operating instructions
3.
Safety instructions
Read the operating instructions carefully and especially observe the safety information. If you do
not follow the safety instructions and information on proper handling in this manual, we assume no
liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
Persons / Product
•
The product may only be installed by a specialist who is familiar with the relevant regulations (e.g. VDE). Electric installations
that are laid or handled incorrectly endanger not only yourself but also others! There is a risk of life-threatening electric
shock!
•
To ensure the safety of the user and protect against accidental contact with dangerous voltages, the product has to be
installed in such a way that makes contact with the terminals impossible. The product must not be operated if it has not been
installed properly.
•
Do not listen to excessively loud music for long periods of time. This may damage your hearing.
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material for children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, flammable gases,
vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe
operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
•
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
•
Also observe the safety and operating instructions of any other devices which are connected to the product.
Miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
•
If you have questions which remain unanswered by these operating instructions, contact our technical support service or
other technical personnel.
4.
Installation and Connection
Make sure that the mounting area can support the weight of the loudspeaker.
The loudspeaker is to be fixed firmly to prevent it from falling and thus to avoid the risk of injuries.
Before cutting out the installation opening ensure that no electric cables, water pipe or are similar are at
risk of damage behind the mounting location.
Be sure to follow the safety instructions of the tool manufacturer when using tools to install your
speaker.
When connecting the device, make sure the connecting cables are not pinched or damaged by sharp
edges.
The connection may only be made to suitable loudspeaker outputs on audio devices.
Make sure that the data for impedance and/or load stated in the Technical Data table are in agreement with
the data for the connected amplifier. Otherwise, damage to the loudspeaker or the amplifier can occur.
The amplifier to which the loudspeaker is to be connected must be disconnected from the power supply
while the connection is being made(unplug the power plug!)
•
Make sure that the installation location has the necessary installation depth (see Technical Data).
•
Saw out the installation opening (for diameter see Technical Data).
•
Lay the loudspeaker cabling from your amplifier's speaker output to the installation location.
•
To mount the loudspeaker, first remove the protective grid from the speaker.
-
To do this, turn the mounting bracket on the loudspeaker enclosure as far as it will go to the outside (fig. 1).
-
Then push the mounting brackets down (fig. 2). By doing so the protective grid will be pushed out of the loudspeaker
enclosure.
•
Before final assembly, connect the loudspeaker to the amplifier. Connect the loudspeaker cables from the amplifier directly
to the flat plug contacts on the loudspeaker:
-
positive loudspeaker cable > red terminal clamp (+)
-
negative loudspeaker cable > black terminal clamp (-)
Hi-fi system connection:
•
Using a screwdriver, set the switch to 8 Ω. The switch is located under the speaker's protective guard.
Electro-acoustic (ELA) system connection:
•
Using a screwdriver, set the switch to the required wattage. The switch is located under the speaker's protective guard.
•
Turn the mounting brackets on the built-in loudspeaker inwards to the stop.
•
Then insert the speaker into the assembly opening (fig. 3).
•
Fasten the loudspeaker by fastening the screws on the mounting bracket clockwise. When this is done, the mounting bracket
will automatically turn outwards until it meets the stop. (fig, 4)
•
Do not replace the loudspeaker protective grid on the loudspeaker enclosure (fig. 5).
All manuals and user guides at all-guides.com
Version 08/12
Regularly clean dust from the speaker.
The surface of the device should only be cleaned with a slightly damp cloth or a dry brush. Never use aggressive cleaning agents
or chemical solutions since these might damage the surface of the casing or impair the operation.
Impedance:
Load capacity (RMS/max.):
Frequency range:
Efficiency:
Magnet:
Voice Coil:
Transformer (100 V):
Installation diameter A:
Installation depth B:
Dimensions (Ø x H):
Weight:
Abbildung 2
Figure 2
Figure 1
Abbildung 1
min. 8 mm
max. 30 mm
Abbildung 4
Figure 4
5.
Cleaning
6.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
7.
Technical data
312060
8 Ω
20 / 45 W
65 – 21000 Hz
85 dB +/-2 dB
227 g
25 mm
1 / 2 / 4 / 8 / 15 W
176 mm
145 mm
213 x 160 mm
1.5 kg
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
Figure 3
Abbildung 3
Figure 5
Abbildung 5
312059
312119
8 Ω
8 Ω
25 / 50 W
35 / 80 W
50 – 21000 Hz
46 – 21000 Hz
86 dB +/-2 dB
87 dB +/- 2 dB
284 g
377 g
25 mm
25 mm
1 / 2 / 4 / 8 / 15 W
1 / 2 / 4 / 8 / 15 W
206 mm
247 mm
138 mm
176 mm
240 x 154 mm
280 x 191 mm
1.8 kg
2.3 kg
V2_0812_02-JU
Advertenties
