Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
G Operating instruction
1. Controls and displays
1.
Time
2.
Battery symbol
3.
Radio symbol
4.
Summertime
5.
Day
6.
Month
7.
Day of the week
8.
Room temperature
9.
Ambient humidity
A.
button
= Settings / confirmation of the setting value
B.
button
= Activation / deactivation of the manual radio signal reception
C.
button
= Increase the current setting value / change the display mode
D.
button
= Reduce the current setting value / switch between °C and °F
E.
Battery compartment
F.
Stand
G.
Cut-out for wall mounting
Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely.
Please keep these instructions in a safe place for future reference. If you sell the
device, please pass these operating instructions on to the new owner.
2. Explanation of warning symbols and notes
Warning
This symbol is used to indicate safety instructions or to draw your attention to
specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
3. Package contents
• "Jumbo" digital radio wall clock
• 4 AA batteries
• These operating instructions
4. Safety instructions
• The product is intended for private, non-commercial use only.
• Use the product only for the intended purpose.
• Protect the product from dirt, moisture and overheating and use it in dry
environments only.
• Do not use the product in the immediate vicinity of heaters, other heat sources
or in direct sunlight.
• As with all electrical products, this device should be kept out of the reach of
children.
• Do not operate the product outside the power limits specified in the technical
data.
• Do not use the product in areas in which electronic products are not permitted.
• Do not use the product in a damp environment and avoid splashing water.
• Do not place the product near interference fields, metal frames, computers, TVs,
etc. Electronic devices and window frames can negatively affect the product's
functionality.
• Do not drop the product and do not expose it to any major shocks.
• Do not modify the product in any way. Doing so voids the warranty.
• Keep the packaging material out of the reach of children due to the risk of
suffocation.
• Dispose of packaging material immediately in accordance with the locally
applicable regulations.
2
Warning – Batteries
• When inserting batteries, note the correct polarity (+ and - markings) and
insert the batteries accordingly. Failure to do so could result in the batteries
leaking or exploding.
• Only use batteries (or rechargeable batteries) that match the specified type.
• Before you insert the batteries, clean the battery contacts and the polar
contacts.
• Do not allow children to change batteries without supervision.
• Do not mix old and new batteries or batteries of a different type or make.
• Remove the batteries from products that are not being used for an extended
period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a fire.
• Keep batteries out of the reach of children.
• Never open, damage or swallow batteries or allow them to enter the
environment. They can contain toxic, environmentally harmful heavy metals.
• Immediately remove and dispose of dead batteries from the product.
• Avoid storing, charging or using the device in extreme temperatures and
extremely low atmospheric pressure (for example, at high altitudes).
5. Getting started
5.1. Inserting the battery
Open the battery compartment cover (E), remove the contact interrupter and close
the battery compartment cover (E) again. The clock is ready for operation.
5.2. Changing the battery
• Remove and dispose of the spent battery if required. Insert four new batteries
(AA). Take care to ensure the correct polarity as shown in the diagram in the
battery compartment (E).
5.3. Low battery
• As soon as the battery symbol
battery capacity is very low. Change the battery immediately.
6. Installation
Warning - installation instructions
• Before mounting, check that the wall you have chosen is suitable for the weight
to be mounted. Also make sure that there are no electric, water, gas or other lines
running through the wall at the mounting site.
• Obtain suitable attachment material from specialist retailers.
• Do not mount the product above locations where persons might sit or stand.
• You can attach the wall clock to a wall using the cut-out on the back (G).
• Alternatively, place the wall clock on a flat surface using the stand (F).
7. Operation
Information - entry
Hold the
button (C) or
button (D) down to
select the values more quickly.
7.1 Automatic adjustment according to the DCF signal
• After the batteries are inserted, the clock automatically starts to search for a DCF
signal. The radio symbol (3) flashes during the search process.
(2) appears on the wall clock's display, the
Advertenties
Inhoudsopgave
