Download Inhoudsopgave Inhoud Print deze pagina
Berker 7531 31 07 Bedienings- En Montagehandleiding
Berker 7531 31 07 Bedienings- En Montagehandleiding

Berker 7531 31 07 Bedienings- En Montagehandleiding

Advertenties

Beschikbare talen

Beschikbare talen

Operating and assembly instructions
Bedienings- en montagehandleiding
7531 31 07
Universal dim actuator
3gang RMD
Universele zelflerende
dimmer 3-voudig DIN-rail
8031 30 07
Universal dim actuator
3gang RMD,
system-/easylink
Universele zelflerende
dimmer 3-voudig DIN-rail,
easylink
1
Berker GmbH & Co. KG - Klagebach 38 - 58579 Schalksmühle/Germany - Tel. + 49 (0) 23 55/90 5-0 - Fax + 49 (0) 23 55/90 5-111 - www.berker.com -
All manuals and user guides at all-guides.com
Safety instructions
Electrical equipment may only be installed and
assembled by a qualified electrician in accord-
ance with the relevant installation standards,
guidelines, regulations, directives, safety and
z
accident prevention regulations of the country.
i
Failure to comply with these instructions may
result in damage to the device, fire or other
hazards.
Hazard due to electric shock. Disconnect be-
fore working on the device or replacing illumi-
nants. Take into account all circuit breakers
that supply dangerous voltages to the device.
Hazard due to electric shock. The device is not
suited for safe disconnection of the mains sup-
ply. Even when the device is switched off, the
load is not galvanically separated from the
mains supply.
Hazard due to electric shock on the SELV or
PELV installation. Do not connect any loads for
low voltage SELV, PELV or FELV together.
Do not connect any LED or compact fluores-
cent lamps that are not expressly suitable for
dimming. The device could get damaged.
Do not connect lights with integrated dimmer.
Do not connect capacitive load and inductive
loads together on the output.
The permissible maximum load per device
must not be exceeded.
These instructions are an integral component
of the product and must be retained by the end
user.
Design and layout of the device
(10)
(1)
(2)
ε
(3)
Figure 1: Device overview
(1) Slide switch auto/min/max/manu
(2) Illuminated button for dimming mode
(3) KNX bus connection terminal
(4) Connection of loads
(5) Slide switch channel selection
(6) Illuminated programming button
(7) Operation button for manual operation with
status LED
(8) Control LED short-circuit and overload protec-
tion per output
(9) Control LED overheating protection
(10) Mains connection
Function
z
System information
This device is a product of KNX system and corre-
sponds to the KNX guidelines. Detailed specialised
knowledge obtained from KNX training courses
is required for comprehension. The planning,
installation and commissioning of the device is
carried out with the help of KNX-certified software.
Systemlink commissioning
The function of the device is software-depend-
ent. The software is to be taken from the product
database. You can find the latest version of the
product database, technical descriptions as well as
conversion and additional support programmes on
our website.
Easylink commissioning
The function of the device is configuration-de-
pendent. The configuration can also be done using
devices developed specially for simple setting and
start-up.
This type of configuration is only possible with
devices of the easylink system. Easylink stands for
easy, visually supported start-up. Preconfigured
standard functions are assigned to the in/outputs
by means of a service module.
Functional description
The device has three load outputs that can be
combined variably using a slide switch to increase
loads. It works with automatic load detection
depending on the connected load in the phase
cut-on or phase cut-off and enables switching and
dimming via the KNX bus of:
- Incandescent lamps and halogen lamps
- Low-voltage halogen lamps with conventional
(9)
- dimmable LED and energy-saving lamps
Additionally, the device has a learn function for
more efficient control of energy-saving lamps and
230 V LED lamps.
(8)
Correct use
(7)
- Dimming of electric consumers AC 230 V
- Installation on DIN rail according to
(6)
ε
ε
(5)
Product characteristics
- Status display of the outputs on the device
- Manual activation of the outputs on the device
(4)
- Automatic load detection
- Setting the minimum and maximum dimming
- Timer functions
- Scene function
- Forced position by higher-level controller
Short-circuit and overload protection
Short-circuit and overload are signalled via the
control LED (8). The load is throttled (see Trouble-
shooting).
Overheating protection
Overheating of the device is signalled by a perma-
nent light of the control LED (9). The connected
load is throttled (see Troubleshooting).
or electronic transformer
DIN EN 60715 in distribution box
is possible, building site operation
value

Advertenties

Inhoudsopgave
loading

Samenvatting van Inhoud voor Berker 7531 31 07

  • Pagina 1 LED (9). The connected (10) Mains connection load is throttled (see Troubleshooting). Berker GmbH & Co. KG - Klagebach 38 - 58579 Schalksmühle/Germany - Tel. + 49 (0) 23 55/90 5-0 - Fax + 49 (0) 23 55/90 5-111 - www.berker.com -...
  • Pagina 2 All manuals and user guides at all-guides.com Operation Connect device „ Connect bus cable via connecting terminal (3). „ Connect load (11) on the lower terminal strip (4) Manual operation of the device. Bus or mains power supply is present. Start-up „...
  • Pagina 3 All manuals and user guides at all-guides.com Troubleshooting The device is ready for operation. The dimming The brightness value can be set by manual button of an operating unit has been programmed operation on the device or by the programmed with the taught-in output.
  • Pagina 4: Opbouw Van Het Apparaat

    De aangesloten belasting wordt gesmoord (10) Netspanningsaansluiting (zie hulp in geval van problemen). Berker GmbH & Co. KG - Klagebach 38 - 58579 Schalksmühle/Germany - Tel. + 49 (0) 23 55/90 5-0 - Fax + 49 (0) 23 55/90 5-111 - www.berker.com -...
  • Pagina 5: Inbedrijfstelling

    All manuals and user guides at all-guides.com Informatie voor de elektrotechnisch (11) belasting De instelling kan via de handbediening op het apparaat of via de geprogrammeerde dimtoets installateur „ Buskabel via aansluitklem (3) aansluiten. van een bedieningsapparaat worden uitge- „ Belasting (11) op de onderste klemstrook (4) Montage en elektrische aansluiting voerd.
  • Pagina 6: Hulp Bij Problemen

    All manuals and user guides at all-guides.com Bijlage Garantie Verlichting Dimmodus toets (2) Wij behouden ons het recht voor om technische Technische gegevens en formele wijzigingen aan het product aan te geel Energiespaarlampen (CFL) Voedingsspanning 230V~ +10/-15% brengen, voor zover deze de technische vooruit- violet Capacitieve last via net...

Deze handleiding is ook geschikt voor:

8031 30 07

Inhoudsopgave