Advertenties
Beschikbare talen
Beschikbare talen
7. Technical data
Dimensions L x W x H
Speed
890/1260/1760/2600 min
Max. workpiece size
Max. workpiece
diameter
Spindle head thread
Weight
Engine
Rated input
Subject to technical changes
* Operating mode S2 – short-term operation
Operation at a constant load for 15 minutes or less,
followed by a time out of operation and a pause of
sufficient duration to allow the machine to cool to
within 2 K of the ambient temperature.
The noise and vibration levels have been determined
in accordance with EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total
vibration emission values (vector sum of three direc-
tions) determined per EN 61029.
8. Unpacking
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of
the warranty period.
• Familiarise yourself with the product by means of
the operating instructions before using for the first
time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number
as well as type and year of manufacture for your
equipment.
24 | GB
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
890 x 325 x 414 mm
-1
500 mm
350 mm
M18 x 2,5
18 kg
230-240 V / 50 Hz
400 W S2 15 min
71 dB(A)
3 dB
84 dB(A)
3 dB
m ATTENTION!
The device and the packaging material are not
children's toys! Do not let children play with
plastic bags, films or small parts! There is a dan-
ger of choking or suffocating!
9. Assembly
Setting up the lathe (Fig. 1)
1. Place the lathe on a firm surface.
2. Screw the lathe to the surface. Use the two holes
in each of the two feet (7) for this.
3. You can use the hexagonal bolts (17) supplied
with the lathe for this.
4. Place the standard washer and spring washer on
the hexagonal bolt (17) (see Fig. 1).
5. Screw the lathe to the surface with the help of the
hexagonal bolt, standard washer, spring washer
and nut (17).
Fitting/replacing the workpiece mount (Fig. 2)
m ATTENTION!
Switch the device off and pull out the mains plug.
Fitting the 4-prong centre tip
1. Loosen the face plate (13) if necessary. To do this,
hold the drive shaft (18) firmly in place with the
open-ended spanner (16) and unscrew the face
plate (13) from the drive shaft (18).
2. Hold the drive shaft (18) firmly in place with the
open-ended spanner (16).
3. Tighten the 4-prong centre tip (1) onto the drive
shaft using the second open-ended spanner (16).
For turning bowls or pots, for example, the face plate
(13) must be used instead of the 4-prong centre tip
(1).
Mounting the face plate
1. If necessary, loosen the 4-prong centre tip (1). To
do this, place the two open-ended wrenches (16)
on the drive shaft (18) and on the 4-prong centre
tip (1) and unscrew the 4-prong centre tip (1).
2. Hold the drive shaft (18) firmly in place with the
open-ended spanner (16).
3. Screw the face plate (13) onto the drive shaft (18).
Advertenties
