Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Getting started.
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING
THE APPLIANCE:
• Make sure the base is plugged in for use.
• Never run the appliance while empty.
• Appliance accessories are not intended to be
used in the microwave as it may damage the
accessories.
•
Never
leave the appliance unattended while in
use.
Never blend hot or carbonated liquids or ingredients
when using any sealed nutribullet cups.
Heated ingredients can pressurize sealed
containers when agitated and violently expel hot
contents upon opening. Always start the blending
process with room temperature or refrigerated
ingredients and liquids (21°C or cooler).
Use extra caution when blending hot liquids or
ingredients in the pitcher.
Steam and splatters can escape through the
vented lid, potentially causing scalding and/
or burns.
NEVER
blend hot liquids in your
pitcher without the pitcher lid and vented lid
cap attached. The vented lid cap is ventilated
to allow steam and pressure to release, while
guarding against excess splashing.
blend hot liquids in your nutribullet cups or
any other sealed vessel, only use the vented
pitcher.
When blending hot liquids in the vented pitcher,
add liquid and solid ingredients to your pitcher
below their respective MAX lines. Attach the
pitcher lid with the vented lid cap inserted. Press
POWER
, then select desired program or begin
LOW
blending on
setting. Once ingredients are
integrated and the mixture is level (no splashing),
increase speed as needed.
Always use care when opening the pitcher lid
after blending hot ingredients making sure that
excess pressure has been released.
8
Pitcher assembly & use.
Review all warning and caution statements in the
Important Safeguards section (pg 3-6) and on the
previous paragraph before proceeding to Step 1.
1
Place the motor base on
a clean, dry, level surface
such as a counter or
table.
2
Place the pitcher on a
clean, dry surface. Add
the ingredients to the
pitcher, making sure they
do not exceed the MAX
line.
NOTE:
pitcher is marked with two
MAX lines: one for solid
ingredients (higher line)
and one for liquids (lower
line). When filling the
blender, make sure your
ingredients do not exceed
their respective MAX lines.
NEVER
3
Place the lid on top of
the pitcher and press
down firmly until locked
in place. Place the lid cap
over the lid opening, then
press down and twist until
locked in place.
NOTE:
run unless the lid is locked
in place.
4
Place the pitcher
(lid-side up) onto Place
the pitcher on a clean,
dry, level surface. Add
the ingredients to the
pitcher, making sure
they do not exceed the
MAX
NOTE:
the pitcher slightly until you
feel it settle into the grooves
on top of the base.
The blending
NOTE:
If you need to add additional
ingredients while blending, switch the setting
LOW
to
and remove the lid cap from the
pitcher lid, leaving the lid attached. Add
The motor will not
ingredients through the hole in the top of
the lid, followed by the tamper if necessary.
Replace the lid cap, then increase to your
desired speed.
through the vent hole when blending
ingredients.
line.
You may need to twist
5
Plug the power cord into
an electrical outlet and
press
POWER
to turn
on the blender. Once the
pitcher is fully locked and
the unit is plugged in, the
Blending Control Panel
will
illuminate and the unit will
be ready to operate.
NOTE:
If pitcher lid and pitcher
are not fully secured onto the
base, control panel will not
illuminate.
6
To begin blending,
select
a manual speed or
program on the
Blending
Control
Panel. To pause
blending, press the current
speed or program once,
the unit will stop running
and the timer will pause.
To
resume blending,
press a
manual speed or the same
program again.
NOTE:
Go to the blending
control panel section on pages
20-23 for speed and program
definitions, images, and other
information.
nutribullet
DO NOT
attempt to add items
HOT
assembly & use.
CAUTION:
Do not use
Review all warning and caution statements in the
any apparatus other
Important Safeguards section (pg 3-6) and on the
than the tamper to push
previous page before proceeding to Step 1.
ingredients toward the
blade. The tamper is
specifically designed
not to come in contact
with the blade. Spatulas,
spoons and other tools
are long enough to reach
the blade, which may
result in damage to the
machine, damage to
property, and possible
injury.
7
When you have reached
your desired consistency,
stop the appliance by
pressing
POWER
. If you
are using a program, you
will hear a beep when the
program has completed.
Wait for the blades to stop
turning. The unit will enter
idle-mode. The timer will
Blending
reset and the
Control Panel
will remain
POWER
illuminated. Press
again to turn off the
unit completely and the
illuminated display will
turn off.
8
Twist pitcher
counterclockwise and lift
off the motor base.
our and enjoy!
WARNING:
Blades are
sharp. Never insert your
hands into the pitcher.
NOTE:
Press up with your
thumb on the tab near handle
first to loosen pitcher lid for
easy removal!
cup
®
1
Place the motor base on
a clean, dry, level surface
such as a counter or table.
9
Advertenties
Inhoudsopgave
