Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Inserting and removing a cutter
■ Put the machine on its side on the table
with the router base pointing towards you.
■ Depress the lock knob and keep it
depressed.
■ Loosen the collet nut and place a cutter
in the collet.
■ Tighten the collet nut firmly using the wrench.
■ Release the lock knob.
■ In order to remove the cutter, proceed in
reverse order.
Always remove the mains
plug from the socket first
before inserting or removing
Replacing the collet
■ Put the machine on its side on the table
with the router base pointing towards you.
■ Remove the collet nut. If a cutter has
been placed, remove it as well.
■ Remove the collet. If necessary, use a pair
of pliers.
■ Place the collet with the required diameter.
■ Replace the collet nut.
Setting the depth stop
The depth stop is used to set the maximum
cutting depth.
■ Loosen the locking bolt (10).
■ Move the depth stop (8) using the adjustment
wheel.
■ Set the required cutting depth using the scale .
■ Tighten the locking bolt.
Setting the cutting depth
■ Set the depth stop (8).
■ Slacken the clamping lever (6).
■ Push the machine down to the depth stop.
■ Tighten the clamping lever.
Quick-selecting the cutting depth
Using the revolver-depth stop it is possible
to quick-select between pre-set cutting depth
positions. The position right below the depth
stop (8) defines the cutting depth.
■ Lift the revolver-depth stop (9) from its current
fixing point and turn the desired cutting depth
position to the position below the depth stop (8).
■ Make sure that the revolver-depth stop is
secured in the fixing point.
■ Follow the instructions below 'Setting the
cutting depth'.
Fine-adjusting the cutting depth
For fine adjustment of the cutting depth,
turn the fine adjustment knob (12).
a cutter.
Fine adjustment
When the approximate depth is set, you can make
fine adjustments by means of the fine-adjustment
knob. To adjust, turn it in clockwise or
anticlockwise direction.
Cutting in serval operations
For cutting in depth and in stages, use the length-
stop turret as an aid. Using the depth scale, set
the desired depth to the lowest depth-stop
position on the turret. Rotate the turret so that
the highest point is under the depth stop and
execute the first cut. Repeat the cut with the
second-highest setting and finally with the last
setting. You can also use two positions if the
desired depth is reached in two operations..
Mounting and adjusting the parallel guide
The parallel guide is used for routing along
edges.
Locate the parallel stop and the guide rods. Push
the guide rods into the casting and secure
them with the adjusting screws (8). Inspect the
machine base and the four securing points.
Loosen the locking screws and push the guide rods
into the machine base (9). The parallel
stop is continuously adjustable and permits various
parallel cuts.
Circle cutting accessories
The centre point is used for routing circles.
These allow you to cut perfect circles in
workpieces. Attach one of the parallel guide rods in
the machine base. Mount the circle-cutting
accessory at the other end. You can attach this
accessory to any position on the guide rod. Position
the tip of the circle-cutting accessory at the centre of
your circle.
Press it slightly so that the tip is firmly in the wood.
You can now cut the circle.
■ Remove a guide rod from the parallel
guide.
■ Mount the centre point to the guide rod .
■ Slide the guide rod in the router base
and tighten the locking bolt.
Switching on and off
■ To switch the tool on, keep the lock-off button
depressed and press the on/off switch.
■ To switch the tool off, release the on/off switch
Adjusting the cutting speed
■ To adjust the cutting speed, turn the
adjustment wheel.
Turn the knob to increase or decrease the speed.
The smaller the cutter head, the higher the
speed.The larger the cutter head, the lower the
speed. A cutter head which runs too fast
causes scorching of the workpiece and leaves
burnt marks.
CAUTION: Do not change the speed when the
machine is working under load.
Cutting direction
Advertenties
Inhoudsopgave
