Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
• Never touch a time switch that shows signs of damage, as this could cause a fatal
electric shock!
First, switch off the mains voltage to the socket to which the time switch is con-
nected (switch off at the corresponding circuit breaker or remove the safety fuse
or switch off at the corresponding RCD protective switch, so that the socket is fully
disconnected).
Only then can you remove the time switch from the mains socket. Do not use the
damaged time switch any longer and dispose of it in an environmentally-friendly
manner.
Preparation
Type plates in different languages are included in the package. Stick the language plates in
your language over the German language label on the back of the time switch.
Initial operation
Plug the time switch (without any device plugged in!) into a suitable mains socket (with
a protective earth conductor).
If the time switched is used outdoors, plug it only into an IP44 wall outlet with earth contact.
You must only use it in the position described below. The socket must be on top, the wheel for
setting the time at the bottom. Both covers must open upwards.
Top
Bottom
Setting the time
Lift the transparent cover with one hand. Turn the outer ring with the hours printed on it
clockwise with the other hand until the arrow " " on the inner ring shows the current time.
Close the cover.
Turn the setting ring only clockwise to the right; it is easy to move.
It is not possible to turn it anti-clockwise! Do not exert any force! If the time switch is
damaged due to that, the warranty will be void!
The time switch only works when it is supplied with electricity, i.e. when it is connected to an
active mains socket.
Setting the on/off times
You can set the times for switching the connected device on and off with the 48 segments
(2 per hour) in a 30-minutes raster. A segment pressed down activates the socket (voltage on,
connected device on), a segment pushed upwards or pulled out switches the socket off (no
voltage, the connected device is off).
Example: If you wish a lamp to be switched on between 22:00 and 23:00, press the two
segments between 22:00 and 23:00 downwards. All the other segments must be pulled out.
Due to the design of the time switch (mechanical operation and switch process;
48 shift segments for 24 hours), deviations from the switching times will occur.
For switching processes or switching times that require accuracy, electronic timer
switches should be used instead.
However, the mechanical time switch has the great advantage that a setting can be
made very quickly.
Connecting a device to the time switch
• Switch the device off.
• Flip the cover of the time switch outlet open and hold the cover with one hand.
• Plug the device into the time switch outlet; push the plug fully into the outlet of the time switch.
• Slowly close the cover of the time switch (do not let it flip shut).
• Switch the device on.
Care and cleaning
Before cleaning the product, disconnect the appliance from the time switch. Disconnect then
the time switch from the power supply by pulling it out of the mains socket.
Never use abrasive cleaning agents, rubbing alcohol or other chemical solutions, since these
could damage the housing or even impair operation.
Use a dry, lint-free cloth to clean the product.
Disposal
Electronic devices are recyclable material and do not belong in the household
waste. Dispose of an unserviceable product in accordance with the relevant statu-
tory regulations.
Technical data
Operating voltage .................................230 V/AC, 50 Hz
Connection power ................................. Resistive load: max. 3680 W (230 V/AC, 16 A)
Devices with mainly resistive load are, e.g., light bulbs, heaters, etc.
Powered devices with inductive load are, e.g., motors, control gears, conventional
transformers, energy-saving bulbs, etc.
Protection class ....................................I
Protection type ......................................IP44
Switch type ...........................................Micro-switch (single-pole)
Smallest switchable time unit ...............30 min (48 switch segments for 24 hours)
Enhanced protection
against accidental contact ....................yes
Operating conditions .............................Temperature -20 °C to +40 °C
Dimensions ...........................................150 x 55 x 83 mm (L x W x H, including plug)
Weight ..................................................138 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2021 by Conrad Electronic SE.
Inductive load: max. 460 W (230 V/AC, 2 A)
1529040_V2_0221_02_VTP_m_en
Advertenties
Inhoudsopgave
