DISPLAY CONTROL
When the refrigerator door is closed and there is no button operation in 3 minutes, the display light
goes off.
When the display light is off, open the refrigerator door or click any button to light it up.
TEMPERATURE SETTING
1) Click the "refrigerator" or "freezer" button and when it flickers in the symbol, temperatures can be
set; each time when the button is clicked, the temperature changes accordingly (the display shows the
temperature accordingly). (Temperatures cannot be set under functions of fast cooling, fast freezing,
SmartECO and vacation,)
2) Under temperature setting, if there is no button operation in 5 seconds, the button stops flickering
and the set temperature comes into effect.
3)Temperature cycle
Refrigerator: 2
C→ 3
C→ 4
O
O
Freezer: -24
C→ -23
C→ -22
O
O
SMARTECO
Under SmartECO, it is 4
Temperatures cannot be changed and you can click the temperature zone button to check the temper-
ature.
1) To enter SmartECO
Click "option" until it flickers and then click "OK" to enter this function.
2) To quit SmartECO
Under SmartECO, click "option" until it goes to SmartECO, click "OK" to quit this function and the light
goes off.
Temperatures of each chamber go back to the value before SmartECO function.
FAST COOLING
Under fast cooling, it is 2
1)To enter fast cooling
Click "option" until it flickers in "fast cooling" and then click "OK" to enter this function.
2) To quit fast cooling
Under fast cooling, click "option" until it goes to "fast cooling" and then click "OK" to quit this function.
The light in fast cooling goes off and the refrigerator temperature goes back to the value before fast
cooling.
FAST FREEZING
Under fast freezing, refrigerator temperature can be set but not for the freezer temperature.
1) To enter fast freezing
Click "option" until it flickers in "fast freezing" and then click "OK" to enter this function.
2) To quit fast cooling
Under fast freezing, click "option" until it goes to "fast freezing" and then click "OK" to quit this function.
The light in fast freezing goes off and the freezer temperature goes back to the value before fast
freezing.
When fast freezing time is up (26 hours), it quits automatically.
When it goes to SmartECO, fast freezing stops.
VACATION
Under vacation, it is 14
1) To enter vacation
Click "option" until it flickers in "fast freezing" and then click "OK" to enter this function.
2) To quite vacation
Under vacation, click "option" until it goes to "vacation" and then click "OK" to quit this function.
The light in vacation goes off and the refrigerator temperature goes back to the value before vacation.
Vacation quits under functions of SmartECO and fast cooling.
POWER OFF MEMORY
With this design, the refrigerator can automatically keep all the setting in case of power off. When the
unit is plugged in again, the refrigerator will run with the setting before power off.
POWER-ON DELAY
To prevent harm to the refrigerator in case of sudden power cut and power on, the unit does not start
immediately if the power off time is less than 5 minutes.
FREEZER OVER-TEMPERATURE ALARM (ONLY IN CASE OF POWER ON)
When the freezer temperature is higher than 10
light of the freezer chamber goes on and the number representing temperature flickers.
Press any button or wait for 5 seconds, flickering stops and it goes back to the temperature that was
set.
REFRIGERATOR DOOR OPENING ALARM
When the refrigerator is open over 3 minutes, the buzzer will buzz. Close the door or press any button
to stop the alarm, but for the latter, the alarm will go off again after 3 minutes.
Sensor fault alarm
When it shows "E0", "E1", "E2" or other abnormal symbols, it means sensor faults and the refrigerator
needs repair.
C→5
C→ 6
C→ 7
O
O
O
C→ -21
C→ -20
O
O
C in the refrigerator and -18
O
C in the refrigerator and the refrigerator temperature cannot be changed.
O
C in the refrigerator and the temperatures in this chamber cannot be changed.
O
C→ 8
C→ OFF→ 2
O
O
O
C→ -19
C→ -18
C→ -17
O
O
O
C in the freezer.
O
C at the first time connected to power, the symbol
O
- 18 -
C
C→ -16
C→ -24
C
O
O
O