Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ELECTROMAGNETIC COMPATIBILITY INFORMATION
For all ME EQUIPMENT and ME SYSTEMS
Guidance and manufacture's declaration - electromagnetic emissions
The AN-6019 is intended for use in the electromagnetic environment specified below.
The customer or the user of the AN-6019 should assure that it is used in such an environment.
Emissions test
Compliance
RF emissions
Group 1
CISPR 11
RF emissions
Class B
CISPR 11
Harmonic emissions
Not
IEC 61000-3-2
applicable
Voltage fluctuations/flicker
Not
emissions IEC 61000-3-3
applicable
For all ME EQUIPMENT and ME SYSTEMS
Guidance and manufacturer's declaration - electromagnetic immunity
The AN-6019 is intended for use in the electromagnetic environment specified below. The
customer or the user of the AN-6019 should assure that it is used in such an environment.
IMMUNITY
IEC 60601test
test
level
Electrostatic
± 6 kV contact
discharge (ESD)
± 8 kV air
IEC 61000-4-2
Power frequency
3 A/m
(50/60 Hz)
magnetic field
IEC 61000-4-8
NOTE: U
is the a.c. mains voltage prior to application of the test level.
T
Table 1
Electromagnetic environment-guidance
The AN-6019 uses RF energy only for its
internal function. Therefore, its RF emissions are
very low and are not likely to cause any
interference in nearby electronic equipment
The AN-6019 is suitable for use in all
establishments other than domestic and those
directly connected to the public low-voltage
power supply network that supplies buildings
used for domestic purposes.
Table 2
Compliance
Electromagnetic
level
environment-guidance
± 6 kV contact
Floors should be wood, concrete or
± 8 kV air
ceramic tile.If floors are covered
with synthetic material, the relative
humidity should be at least 30 %.
3 A/m
Power frequency magnetic fields
should be at levels characteristic of a
typical location in a typical
commercial or hospital environment.
For ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING
Recommended separation distances between
portable and mobile RF communications equipment and the AN-6019
The AN-6019 is intended for use in an electromagnetic environment in which radiated RF distur-
bances are controlled. The customer or the user of the AN-6019 can help prevent electromagne-
tic interference by maintaining a minimum distance between portable and mobile RF communica-
tions equipment (transmitters) and the AN-6019 as recommended below, according to the maxi-
mum output power of the communications equipment
Rated
Separation distance according to frequency of transmitter
maximum output power
of transmitter
W
0.01
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in meters (m) can be determined using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, objects and people.
For ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING
Guidance and manufacturer's declaration - electromagnetic immunity
The AN-6019 is intended for use in the electromagnetic environment specified below. The customer
or the user of the AN-6019 should assure that it is used in such an environment.
IMMUNITY
IEC 60601test
test
level
Radiated RF
3 V/m 80 MHz
IEC 61000-4-3
to 2.5 GHz
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones
and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be
predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the measured field strength in the
the location in which the AN-6019 is used exceeds the applicable RF compliance level above,
the AN-6019should be observed to verify normal operation. If abnormal performance is observed,
additional measures may be necessary, such as re-orienting or relocating the AN-6019.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than [V1] V/m.
Table 4
150
80
kHZ
MHz
to 80 MHz
to 800 MHz
0.12
0.12
0.38
0.38
1.2
1.2
3.8
3.8
12
12
Table 3
Compliance
Electromagnetic environment-guidance
level
Portable and mobile RF communications
equipment should be used no closer to any part
of the AN-6019, including cables, than the
recommended separation distance calculated
from the equation applicable to the frequency
of the transmitter.
Recommended separation distance
3 V/m
80 MHz to 800 MHz
800 MHz to 2,5 GHz
Where P is the maximum
output power rating of the
transmitter in watts (W) according to the
transmitter manufacturer and d is the
recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site
a
survey,
should be less than the compliance
level in each frequency range.
Interference may occur in the vicinity
of equipment
Marked with the following symbol:
800
MHz to
2.5 GHz
0.23
0.73
2.3
7.3
23
b
Advertenties
Inhoudsopgave
