Advertenties
Beschikbare talen
Beschikbare talen
GENERAL
• The installation of the system must be done by an authorized person.
• The motor control receiver unit (KP200A) must be safely fixed to the wall or to
the ceiling.
• Make sure that no liquid is exposed to the remote control (KP100A) or
the motor control receiver (KP200A).
• The KP200A unit must be connected to protective earth
KP100A, WIRELESS TRANSMITTER (REMOTE CONTROL)
KP100A is a transmitter (single channel) and is compatible with the motor
control receiver KP200A. The transmitter transmits through radio waves
(RF).
SPECIFICATIONS FOR KP100A
• The used frequency is 433,92 Mhz
• Power supply: 12 volts battery
• Battery Alkaline, type 23A
• Working temperature: +5 to +40 degree Celsius
BATTERY LIFE
The transmitter is working with battery, the normal lifetime of the battery
is over 1 year when used 3-4 times every day.
KP200A, MOTOR CONTROL RECEIVER (CONTROL BOX)
KP200A is the control box for the connected motor. With this control box
you operate the projection screen.
SPECIFICATION KP200A
Power supply: 100-240 v, 50/60 Hz
• Working temperature: +5 to +40 degree Celsius
• Rated load: <400 W Power
• Emission frequency: 433,92 Mhz
• Fuse 6,3 A
PROGRAM SETTINGS
The equipment are programmed to match each other when delivered with
a screen, othervise program as below.
FUSE
If the control box is not working, unplug the control box from AC-power
and then check the fuse on the circuit board. Open the two covers (8 pcs of
screws) on the backside of the control box until you see the circuit board.
The fuse is in the plastic box marked "Fuse".
CONNECTIONS, SEE FIG. 1
AC power and connection to the motor:
MC-: Motor counter-clockwise
MC+: Motor clockwise
:
Motor protection earth
N:
Motor Neutral
:
AC_IN power protection earth
N:
AC_IN power Neutral
L:
AC_IN power Line
12V TRIGGER CONNECTION (2 PINS)
T-:
12-volt trigger input's ground
T+:
12-volt trigger input's signal
LINE IR CONNECTION (2 PINS)
IR-:
Line IR input's ground
IR+: Line IR input's signal
EXTERNAL CONTROL OF THE RELAYS (3 PINS)
Connection for ground
Out2 Connection for UP
Out1 Connection for DOWN
HOW TO CONNECT AND PROGRAM THE CONTROL BOX
In this section you will learn how to set the control box into the
programming mode and to pair equipment to the control box.
1. Pairing with RF-remote control
2. Pairing with IR-remote control
3. Erase all previous programming (reset to default codes)
4. Connecting with Line IR Control module
5. Connecting 12-volt trigger
6. External control of the relays
GO INTO PROGRAMMING MODE:
• Press and hold down the STOP button of the receiver unit for more than 5
seconds, when the LED starts to blink, release the STOP button, you are in
the programming mode now.
• You can now pair the control box with RF/IR equipment or erase the
programming (subject 1-3):
1. PAIRING WITH RF-REMOTE CONTROL
The remote control is paired with the control box, if the programming is
erased or if the units not are paired you need to do as follows:
INSTALLATION AND OPERATIONS GUIDE (ENG)
.
1. Enter programming mode
2. Open the battery cover on the remote control and press the black
button once. The pairing code will now be sent to the receiver unit.
3. When the pairing is done the LED will lit continuously.
4. You can now use the controller devices
If no pairing is done in 30 seconds the receiver will leave programming
mode automatically.
2. PAIRING WITH IR-REMOTE CONTROL
You can use the control box with many of the IR-remote controls on the
market. If using the default codes, see page 7, you don´t need to do any
pairing to the control box (but your own IR-remote control will need some
programming).
To pair the control box you do as follows:
1. Enter programming mode
2. LED is blinking slowly. Press the key on the remote that you want to
use as "UP", when accepted the LED will blink faster, press the same
key once again. If the code is acceptedthe LED will be dark for 2 sec
and then blink slowly, go to next step. If not accepted, go to step 1
or as *.
3. LED is blinking slowly. Press the key on the remote that you wantto
use as "STOP", when accepted the LED will link faster, press the same
key once again. If the code is accepted the LED will be dark for 2 sec
and then blink slowly, go to next step. If not accepted, go to step 1
or as *.
4. LED is blinking slowly. Press the key on the remote that you want to
use as "DOWN", when accepted the LED will blink faster, press the
same key once again. If the code is accepted the LED will be dark for
2 sec and then lite steady, go to next step. If not accepted, go to step
1 or as *.
5. You can now use the controller devices If sending RF-signals at the
same time as the IR programming is under progress the receiver will
leave the programming mode.
*Some
IR-codes
will
controlbox.
If
the
programming mode will be left and the LED will shine continuously, try
with other buttons or with another remote control.
3. ERASE ALL PREVIOUS PROGRAMMING (RESET TO DEFAULT CODES)
With this function you can erase the programming of all programmed
IR-codes, except the default codes. The control box can only be controlled
with the default IR-codes and the buttons on the control box, the other
equipment has to be reprogrammed.
1.
Go into programming mode
2.
Press UP-button (on the control box) for at least 5 sec, the LED becomes
black, then release the UP-botton.
3.
The LED lit continuously and all the programming is now reset.
4. CONNECTING WITH LINE IR CONTROL MODULE
When
using
the
control
Crestron you can use the default codes, see page 7, (you may
have to program your own control system with our codes).
Connect like this:
1.
Connect the IR input´s ground to the receiver units connection
(see fig. 1) "IR-"
2.
Connect the IR input´s signal to the receiver units connection
(see fig. 1) "IR+"
3.
You can now use the controller devices
5. CONNECTING WITH THE 12-VOLT TRIGGER
If the projector has a 12-volts trigger, you can connect it to the control
box and the screen will go down when the projector is turned on and go
up when the projector is turned off. The trigger function may have to be
activated in your projector.
1.
Connect
the
ground
to
the
(see fig. 1) "T-"
2.
Connect
the
signal
to
the
(see fig. 1) "T+"
When connecting the trigger cords, make sure that the projector and the
control box is powered off.
6. EXTERNAL CONTROL OF THE RELAYS
If you like to control the relays in the control box directly from an external
control system/switch you will use these connections. You set up a contact
closure of the circuit to send the screen down or up. The contact closure
shall be programmed to about 30 seconds to be able to send the screens
down or up no matter size or model.
not
be
accepted
by
code
isn´t
accepted
box
with
a
control
system
12-volt
trigger
receiver
units
connection
12-volt
trigger
receiver
units
connection
the
the
like
input´s
input´s
Advertenties
