Inhoudsopgave
Advertenties
HPD
VERSCHILDRUK
TRANSMITTER
HOLDING REGISTERS
1
Modbus Slave Address
2
Modbus Baud Rate
3
Modbus Parity Mode
4
Device type
5
HW version
6
FW version
7-10
Output Type
11
(Channel 1)
Pressure Range Minimum
12
(Channel 1)
Pressure Range Maximum
13
(Channel 1)
14
Response Time (Channel 1)
15
Min. Pressure Limit (Channel 1)
16
Max. Pressure Limit (Channel 1) unsigned int.
Power-up Timer
17
(Channel 1)
18
K-factor Selection (Channel 1)
Internal Voltage Source PWM
19
(Channel 1)
Network Bus Termination
20
(NBT)
21
Output Type (Channel 2)
Pressure Range Minimum
22
(Channel 2)
Pressure Range Maximum
23
(Channel 2)
24
Response Time (Channel 2)
Min. Pressure Limit
25
(Channel 2)
26
Max. Pressure Limit (Channel 2) unsigned int.
27
Power-up Timer (Channel 2)
28
K-factor Selection (Channel 2)
Internal Voltage Source PWM
29
(Channel 2)
30
Display Mode Selection
Voor meer info omtrent Modbus over een serieel network, bezoek volgende link:
MIW-HPD-NL-000 - 16 / 12 / 16
Data type
Description
unsigned int. Modbus device address
Modbus communication
unsigned int.
baud rate
unsigned int. Parity check mode
unsigned int. Device type (Read only)
Hardware version of the
unsigned int.
device (Read only)
Firmware version of the
unsigned int.
device (Read only)
Reserved, returns 0
Select channel 1 output
unsigned int.
type
Minimum pressure for
unsigned int.
analogue output 1
Maximum pressure for
unsigned int.
analogue output 1
unsigned int. Channel 1 response time
Channel 1 minimum
unsigned int.
pressure limit
Channel 1 maximum
pressure limit
Channel 1 power-up timer.
unsigned int.
It counts the time before
the first detection
Channel 1 K-factor
unsigned int.
selection according to the
motor type
Channel 1 internal voltage
unsigned int.
source selection for the
PWM 1 output
Network bus termination
unsigned int.
resistor state
Select channel 2 output
unsigned int.
type
Minimum pressure for
unsigned int.
analogue output 2
Maximum pressure for
unsigned int.
analogue output 2
unsigned int. Channel 2 response time
Channel 2 minimum
unsigned int.
pressure limit
Channel 2 power-up timer.
It counts the time before
the first detection
Channel 2 power-up timer.
unsigned int.
It counts the time before
the first detection
Channel 2 K-factor
unsigned int.
selection according to the
motor type
Channel 2 internal voltage
unsigned int.
source selection for the
PWM 1 output
unsigned int. Display Mode Selection
www.sentera.eu
terug naar inhoudstafel
Data
Default
1—247
1—3
0 = 8N1
1 = 8E1
2 = 8O1
HPD-X-1K0 = 1071
HPD-X-2K0 = 1072
HPD-X-4K0 = 1073
HPD-X-10K = 1074
XXXX
XXXX
1—3
0—10.000
HPD-X-1K0
50—10.000 Pa
HPD-X-2K0
50—20.000 Pa
HPD-X-4K0
50—40.000 Pa
HPD-X-10K
50—10.000 Pa
1—100
HPD-X-1K0
0—10.000
HPD-X-2K0
0—20.000
HPD-X-4K0
0— 40.000
HPD-X-10K
0—10.000
HPD-X-1K0
0—10.000
HPD-X-2K0
0—20.000
HPD-X-4K0
0— 40.000
HPD-X-10K
0—10.000
0—1.000 s
0—1.000
0—1
0—1
1—3
0—10.000
HPD-X-1K0
50—10.000 Pa
HPD-X-2K0
50—20.000 Pa
HPD-X-4K0
50—40.000 Pa
HPD-X-10K
50—10.000 Pa
1—100
HPD-X-1K0
0—10.000
HPD-X-2K0
0—20.000
HPD-X-4K0
0— 40.000
HPD-X-10K
0—10.000
HPD-X-1K0
0—10.000
HPD-X-2K0
0—20.000
HPD-X-4K0
0— 40.000
HPD-X-10K
0—10.000
0—1.000 s
0—1.000
0—1
0—2
http://www.modbus.org/docs/Modbus_over_serial_line_V1_02.pdf
Values
1
1 =
2
2 =
19.200
3 =
38.400
0 =
1
1 =
2 =
0100 = 0 x HW version 1.00
0100 =
0 x FW version 1.00
1 =
0—10 VDC
1
2 =
0—20 mA
3 =
100,0 Pa
0 1.000 =
1.000 Pa
(HPD-X-10K)
1.000 =
100,0 Pa
10.000
1.000 =
1.000 Pa
10
10 =
0 1.000 =
100,0 Pa
0 1.000 =
1.000 Pa
10.000
20.000
1.000 =
100,0 Pa
40.000
10.000 1.000 =
1.000 Pa
60 s
100 =
0
0 =
0 = 3,3 VDC
0
1 =
1 = 12 VDC
0 =
Disconnected
0
1 =
Connected
1 =
0—10 VDC
1
2 =
0—20 mA
3 =
1.000 =
100,0 Pa
0
1.000 =
1.000 Pa
(HPD-X-10K)
1.000 =
100,0 Pa
10.000
1.000 Pa
10
10 =
0 1.000 =
100,0 Pa
0 1.000 =
1.000 Pa
10.000
20.000
1.000 =
100,0 Pa
40.000
10.000
1.000 Pa
60 s
100 =
0
0 =
0 = 3,3 VDC
0
1 =
1 = 12 VDC
0 =
Disconnected
0
1 =
Connected
11 - 12
9.600
8N1
8E1
8O1
PWM
1 s
100 s
PWM
1 s
100 s
Advertenties
Inhoudsopgave
