Inhoudsopgave
Advertenties
NL
Deurautomaat voor trekkende of duwende deuren, met ingebouwde veer
Advanced Setting
28)
28)
Output Relay
Set the status relay mode:
Set the status relay mode:
• •
STATUS: activates when the door is in OPEN / OPENING / CLOSING
STATUS: activates when the door is in OPEN / OPENING / CLOSING
• •
SERVICE: it is activated if the partial counter that indicates the maintenance request has exceeded
SERVICE: it is activated if the partial counter that indicates the maintenance request has exceeded
the intervention threshold�
the intervention threshold�
Default value = STATUS
Default value = STATUS
Advanced Setting
29)
29)
FTC-S MODE
Sets the operating mode of the stop photocell in opening
Sets the operating mode of the stop photocell in opening
• •
STOP: the door stops and remains stopped until the FTC-S is deactived� Threshold clear�
STOP: the door stops and remains stopped until the FTC-S is deactived� Threshold clear�
• •
RECLOSE: if the FTC-S is activated, due to an obstacle opening, the door stops and after 4 sec� it
RECLOSE: if the FTC-S is activated, due to an obstacle opening, the door stops and after 4 sec� it
closes again�
closes again�
Default value = STOP
Default value = STOP
Advanced Setting
30)
30)
FTC Test Filter
Allows you to change the delay time to match the delay time of the test signal coming from the safety
Allows you to change the delay time to match the delay time of the test signal coming from the safety
photocells�
photocells�
Default value = 20 mS
Default value = 20 mS [ [exact value to connect Hotron photocells]
Advanced Setting
31)
31)
Magnet Mode
Allows you to change the magnet lock time function when Electrolock is set to Magnet�
Allows you to change the magnet lock time function when Electrolock is set to Magnet�
Position
Position allows the lock to relock on the door closed position i�e� lock relay is active while the door is
allows the lock to relock on the door closed position i�e� lock relay is active while the door is
open�
open�
Timed allows the lock relay to follow the exact time set in Electrolock Time
Timed
allows the lock relay to follow the exact time set in Electrolock Time
Advanced Setting
32)
32)
Fire mode safety
In the event that the FIRE mode is activated, all Safety sensors (FTC, FTC-S) will be overridden
In the event that the FIRE mode is activated, all Safety sensors (FTC, FTC-S) will be overridden
(Fire mode safety = OFF) causing the door to close even though an object or person may be in the door's
(Fire mode safety = OFF) causing the door to close even though an object or person may be in the door's
path of travel, and therefore may be subject to injury� This mode of operation is generally used to isolate
path of travel, and therefore may be subject to injury� This mode of operation is generally used to isolate
the area in the event of a fire.
the area in the event of a fire.
Default value = ON
Default value = ON
Advanced Setting
33)
33)
FTC Test Mode
Het testsignaal voor de veiligheidsfotocellen (FTC/ FTC-S) kan worden ingesteld op "Actief HOOG" of
"Actief LAAG"� Dit kan helpen om af te stemmen op de bedrijfsmodus van verschillende typen fotocellen
van verschillende fabrikanten�
Controleer de bedrijfsmodus van het testsignaal van de gebruikte veiligheidsinrichting en stel de
parameter overeenkomstig in.
OPMERKING: Als de bedrijfsmodus niet overeenkomt, zal de deur niet bewegen.
OPMERKING: Als de bedrijfsmodus niet overeenkomt, zal de deur niet bewegen.
Standaardwaarde = Actief HOOG
Standaardwaarde = Actief HOOG
Output Relay
STATUS/SERVICE
FTC-S MODE
STOP/RECLOSE
FTC Test filter
20 mS
exact value to connect Hotron photocells]
Magnet Mode
Timed
Fire mode safety
OFF / ON
FTC Test Mode
Active
/Active
HIGH
LOW
DIGIWAY SR
37
Advertenties
Inhoudsopgave
