Inhoudsopgave
Advertenties
TO SEARCH FOR A SPECIFIED PTY
1 Press PTY.
The program type of the currently tuned station is displayed.
2 Within 4 seconds, press N
program type.
3 Within 4 seconds, press PTY again.
The search automatically checks every preset station. After
identifying a suitable staiton, the station will be selected.
EON service for the PTY search
When EON service works to transmit PTY, a suitable station is
detected without checking every preset station. When a station
transmits EON information, it takes about 15 to 30 seconds for
the unit to decode the EON information. After decoding the
information, the EON indicator lights up.
When a station is not found
"NOT FOUND" is displayed and the unit returns to the previous
station.
When the TRAFFIC program type is selected
The unit searches for a station transmitting a *
However, the tuned station may not be broadcasting a traffic
announcement currently. Wait for a while. The tuned station
broadcasts traffic infor mation regularly and a traffic
announcement will be made.
EON SEARCH
During FM reception, the unit switches to radio programs with
the specified PTY automatically as soon as they begin.
1 Press PTY.
The program type of the currently tuned station is displayed.
2 Within 4 seconds, press N
program type.
3 Within 4 seconds, press ENTER.
"EON ON" is displayed for 3 seconds. Then, the EON indicator
starts flashing and the unit enters EON search standby mode.
When radio program with the specified PTY in another radio
station begins, it interrupts the currently playing radio program
and the radio program with the specified PTY is heard. At this
time, the EON indicator flashes rapidly.
At the end of the radio program with the specified PTY, the
previous FM radio station is restored.
• EON search standby mode is stored until it is cancelled even
if the power is turned off.
To cancel EON search standby mode
Keep PTY pressed. (Do not release PTY yet.) "EON PTY" and
the specified PTY are displayed alternately. At this time, press
ENTER with pressing PTY. "EON OFF" is displayed and EON
search standby mode is cancelled.
NOTE
The EON search function does not work when:
- FM stations are not preset.
- The signals of stations with the specified PTY are weak.
All manuals and user guides at all-guides.com
N
N / M
N
N
M
M
M to select a
M
7
TP code.
N
N
M
M
N
N / M
M to select a
M
OTHER FUNCTION OF RDS CODES
8
Clock-time (*
CT)
The CT function provides the unit with information about the local
time. Once the CT function is set to on, the clock time will be
updated every hour on the hour whenever a CT station is
received.
To activate the CT function
Hold down CT until "CT ON" appears on the display.
If the clock is set wrongly due to an incorrect clock signal, hold
down CT until "CT OFF" appears to deactivate it.
*
5
Program type identification (PTY)
PTY allows selection of listening by one of 30 or more
program types rather than by a station.
*
6
Enhanced other networks information (EON)
EON information gives the receiver a cross reference
to other stations and allows the receiver to switch from
the currently tuned station to another RDS station.
*
7
Traffic program identification (TP)
This is a code which informs the receiver that a tuned
station regularly broadcasts traffic information.
8
*
Clock-time (CT)
CT function provides an accurate clock signal which is
self-adjusting to time zones and seasonal time changes.
To change the MW tuning interval
The default setting of the MW tuning interval is 9 kHz/step.
If you use the unit in an area where the frequency allocation
system is 10 kHz/step, change the tuning interval as follows.
Hold down BAND/DIGITAL/ANALOG and press POWER
6STANDBY/ON.
To reset the interval, repeat this procedure.
NOTE
When the MW tuning interval is changed, all preset stations are
cleared. The preset stations have to be set again.
En
17
ENGLISH
Advertenties
Hoofdstukken
Inhoudsopgave
