Inhoudsopgave
Advertenties
1.
1
GENERAL DESCRIPTION
Digital keyboard operating with a 9 volt type 6 F22 battery to transfer, by radio (433.92 MHz), fixed length codes,
with 1 to 8 selectable digits. This wireless code keyboard has 9 channels and enables you to control up to 9 devices.
In this case, you have to program 1 code per channel,
channel.
2
TECHNICAL FEATURES
Transmission frequency
433,92 MHz
Distance
Approx. 30 m (in free field)
Type of code
Multipass
Number of channels
9, selectable through the keyboard
Power supply
type 6F22 9 V alkaline battery
Consumption
15 μA in standby
Duration of transmission
Approx. 1 sec.
Protection standard
IP 54
3
APPLICATIONS
The keyboard is indicated in all cases when the activation of a device must be code protected: automatic garage door
or gate openers for example. The keyboard, by its design, does not need wiring and can be used outdoors. The front
unit, composed with digits, is fixed with screws (fig. 2). The keyboard, of semi-transparent conductible rubber, is backlit.
The battery is in the housing.
N.B. BURGLAR-PROOF electronic housing. Access to electronics does not enable activating the control.
4
ASSEMBLY INSTRUCTIONS
Remove the cover, keyboard and electronic circuit. Attach the box. Connect the battery and close the box with the
special screws provided. The system is ready (see photos 1 to 4).
5
OPERATION
Once the system is power supplied, you can start programming the codes.
(See diagram on next page).
a.1st use INSTALLATION CODE:
This code enables you to enter programming mode to modify later your access code. It is advisable to modify the
factory pre-set installation code on 999999. For this, choose a new personal code with 6 digits and follow the pro-
cedure on the diagram (next page).
b. Programming ACCESS CODE:
This code keyboard has 9 channels, then you can control up to 9 devices. Each device (automatic garage door or gate
openers, etc.) can be controlled thanks to the access codes you selected (1 code per channel). You have to choose a
code from 1 to 8 digits for each device you want to control (the first digit must be the channel number).
Examples: 18625 for the channel 1 / 2533 for the channel 2 / 36541779 for the channel 3
c. Erasing ACCESS CODE:
If you make a mistake while programming, push CLEAR and wait until the keyboard switches off, then repeat pro-
gramming.
If you want to modify a code, just program a new code on the same channel, the new entered code cancels and
replaces the previous one.
INSTALLATION CODE
ACCESS CODE
Channel 1:
Channel 2:
Channel 3:
You can note your various
Channel 4:
codes here
Channel 5:
GB
CFI EXTEL WECACV 70003 - 11/2010
2.
L1
Each code has to start with the number of the selected
1
Channel 6:
6
2
Channel 7:
7
3
Channel 8:
8
4
Channel 9:
9
5
3.
L2
Remark:
the channel 1 corresponds to the key A of the remote control
the channel 2 corresponds to the key B of the remote control
the channel 3 corresponds to the key C of the remote control
the channel 4 corresponds to the key D of the remote control
the other channels will control only the receptors of WEATER3 kit.
A
1st use:
Installation code
Type ENTER + 999999+
ENTER to enter
programming code
Leds L1 - L2 lit + BIP for
3s, then
the leds switch off
Type 1 + ENTER
Led L1 lits
Type 999999 + ENTER
Long BIP
Type the new installation
code with (6 digits) +
ENTER
Long BIP
Confirm typing the new
installation code with
(6 digits) + ENTER
Caution:
in case of inactive keyboard for 30 seconds, You go out programming mode. Repeat the procedure
from the beginning.
6
PROGRAMMING THE CODE KEYBOARD
ON THE RECEPTOR OF THE DEVICE TO CONTROL
In order your code keyboard can communicate with the device to control, you should refer to the device instructions
and repeat the same procedure as for programming your remote control. For this programming, instead of pushing a
button of the remote control, dial the access code on the keyboard. The programming is made automatically.
Caution:
Keep your codes on a secure place, because if you forgot them, you will not be able to use your code
keyboard.
Battery level indicator
Push a button:
1) If you hear a short bip when pushing: the battery is good.
2) If you hear a 2 second bip, the battery is charged at 50%.
Any programming is then impossible but the control is possible.
3) If you hear short 3 bips 3 times, the battery has to be changed.
Any programming or control is then impossible
This device is guaranteed for labour and parts in our premises.
The guarantee does not cover: the consumables (batteries, etc.) and the damages caused by: misuse, improper installa-
tion, external intervention, deterioration by mechanical or electrical shock, fall or atmospheric phenomenon.
4.
B
Programming
an access code
Type ENTER + installation code (6 digits)
+ ENTER
Leds L1 - L2 lit + BIP for
3s, then
the leds switch off
Type 2 + ENTER
Led L2 lits + 2 long BIP
Type the channel number (from 1 to 9) + ENTER
Long BIP
Type your access code channel
number (1 to 9) + (0 to
7 digits) + ENTER
Long BIP
Confirm the access code chan-
nel number (1 to 9) +
(0 to 7 digits) + ENTER
Leds L1 and L2 lit + BIP for 3s, then the leds switch off
END OF PROGRAMMING
CFI EXTEL WECACV 70003 - 11/2010
C
Erasing an
access code
Type 0 + ENTER
Long BIP
Type 0 + ENTER
GB
Advertenties
Inhoudsopgave
