Inhoudsopgave
Advertenties
Mounting
The movement sensor can be mounted inside or outside at a height
of approximately 2 metres.
Mount the movement sensor as follows:
• Use a small screwdriver or similar (see Figure A) to remove the
transparent cap on the protective cover.
HOUSE/ON
A
Setting the number code for the address
UNIT/OFF
Press the key for 5 seconds.
no longer than 3 sec. pause
UNIT/OFF
Press the key as often as required for the address and
keep it pressed down the last time (press key briefly five
times for address 5 and keep pressed down fifth time).
...
Appliance address is stored.
Setting the letter code for the address
HOUSE/ON
Press the key for 5 seconds.
no longer than 3 sec. pause
HOUSE/ON
Press the key as often as required for the address and
keep it pressed down the last time (press key briefly three
times for address C and keep pressed down third time).
...
System address has been stored.
MBO 1991 492-401 DA
All manuals and user guides at all-guides.com
• Unscrew the cover and fit the movement sensor with the
2 screws supplied (see Fig. B).
• Install the 2 batteries.
Depending on the setting, the movement sensor will switch on
the light when movement is detected at any time, or only when
it is dark. The switch signals are sent by radio to the Central
Alarm Unit.
The switch off time can be set between 1 min. and 256 min.
Commissioning
Once the 2 batteries have been fitted the movement sensor is
activated. In the default position, address A1 is activated
whenever a movement is detected (day and night) and, once
the last movement has been detected, the light on address A1
will switch off after 1 minute. To test this press the
"HOUSE/ON" and "UNIT/OFF" keys. When you press the
"HOUSE/ON" key the light on address A1 switches on (LED
flashing), but if you press the "UNIT/OFF" key the light on
address A1 switches off (LED flashing).
UNIT/OFF
B
The LED flashes the same number of times that the key was
pressed for the specified address (e.g. once for address 1).
The LED flashes every time the key is pressed and after about
3 seconds as often as the key was pressed for the specified address
(e.g. 5 times for address 5).
The LED flashes the same number of times that the key was
pressed for the specified address (e.g. once for address A).
The LED flashes every time the key is pressed and after about
3 seconds as often as the key was pressed for the specified address
(e.g. 3 times for address C).
13
Xanura™
Movement sensor, RF type BSX1
Adjusting the movement sensor
UNIT/OFF
Briefly press the key.
HOUSE/ON
Press the key for 5 sec.
HOUSE/ON
Release the key.
HOUSE/ON
Press once and keep pressed down for 3 sec.
or
press twice and keep pressed down for 3 sec. second time.
HOUSE/ON
Release the key.
Adjusting the switch-off time
UNIT/OFF
Press the key briefly.
HOUSE/ON
Press the key for 5 sec.
HOUSE/ON
Release the key.
HOUSE/ON
Press once and keep pressed down for 3 sec.
or
press twice and keep pressed down for 3 sec. second time.
... or ...
press nine times and keep pressed down for 3 sec. the ninth time.
HOUSE/ON
Release the key.
Flashes once for 1 minute
Flashes twice for 2 minutes
Flashes three times for 4 minutes
MBO 1991 492-401 DA
14
15 MBO 1991 492-401 DA
Flashes 4 times for 8 minutes
Flashes 5 times for 16 minutes
Flashes 6 times for 32 minutes
Advertenties
Inhoudsopgave
