Inhoudsopgave
Advertenties
In the model with Filter Cartridge (4): do not take off the Filter Cartridge from the Tank Cover
when opening and filling water for the tank.
Important: Soak the filter cartridge in a water bath for 24 hours before the first use (not in the
water tank!). The resin has to absorb water to reach high performance.
3.
Switch on the device by pressing the On/Off switch (11) on the Control Panel (7), the control
display appears blue. The Mist Cap (2) can be turned 360° or used bi-directional to have an
even distribution of moisture..
4.
The desired air humidity level can be selected by pressing the Humidifity button (12) on the
Control Panal. The device will be shut off automatically when the room humidity reaches the
given level. On the Display panel (7), it shows the current humidity level in the room. By press-
ing the Humidifity button (12), you will be able to set the desired humidifity from 40%, 45%,
50%, 60% ,70% and "continous" model. Release the button at your desired humidifity level or
at continous model, the unit is set and the display will switch to show the actual room humidity
level again. Note: on "continous" the unit will NOT turn off automatically.
5.
Caution: the device will not be switched on if the humidity level is set too low.
6.
Pressing the Output button (13) on the control panel, you can change the volume of output
mist from Level 1 to Level 3 (shown on the display panel).
7.
"Warm Mist" button (14): a heater can be switched on by pressing this button. This heater
will heat up the water to 80 C° before it enters into the mist generation chamber. By this pre-
heating function, the temperature of the output mist will reach 40 C°, which will not cause the
room temperature to drop when mist evaporates. A LED light on top the display panel will be
switched on when this pre-heating function is turned on. Press this button again to switch off is
function, and the LED light will be switched off.
8.
"Night Mode" button (15): Pressing this button, the device is switched to "night mode" with dim
LED light. Press again, the device is back to normal light mode. During this mode, the relative
humidity will be kept at a comfort level of 45%.
9.
"Auto Mode" button (16): This button can set the humidifity level at 45% and the ventilator
works at the optimal level 1. By pressing this button, the previous humidity level set by "Humid-
ity" button will be canceled.
10. "No water" alarm light: At the lower part of the display panel, there is red LED alarm light. This
light will on when there is no water or not enough water in the mist generating chamber. When
this light is on, you should switch off the unit buy press the " On/Off Switch" and refill the Water
Tank with fresh water, put it back onto the unit and switch on the unit again.
11. Note: turn off the unit before taking off the tank. You need to turn on the unit again when placing
the tank back to the unit.
12. Althrough the unit shuts off its motor and its transdusor automatically when water runs off
and the "No water" LED light turns on, in order to avoid unexpected damages, we recommend
you to switch off the unit by pressing the On/Off Button as soon as the "No water" Light is on.
CLEANING PROCEDURE
Switch off the device and unplug the power cable from the socket before all maintenance work
•
and after each use.
Never submerge the device in water (this can result in short-circuiting). To clean the device,
•
simply wipe it with a damp cloth and then dry it thoroughly. Always ensure the power cable has
been unplugged beforehand.
Descale the humidifier as appropriate for the hardness of the water, but at least once a week:
•
First remove the water tank (the upper section) and clean it with a brush. Descale the device
with a standard descaler and then rinse it thoroughly. Reassemble the device completely be-
fore use.
Thoroughly rinse out the water tank on a regular basis.
•
Replace Filter Cartridge (4) every 1-2 months as appropriate for the hardness of the water.
•
10
Advertenties
Inhoudsopgave
