Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ENGLISH
1
Safety guide
2
Shaft lock
3
Socket wrench
4
Cut-off wheel
5
Inner flange
6
O-ring
7
Spindle
8
Ring
9
Outer flange
10 Hex bolt
11 Screw
12 Spark guard
SPECIFICATIONS
Model
Wheel diameter .................................................................................................................................................. 355 mm
Hole diameter .................................................................................................................................................... 25.4 mm
–1
No load speed (min
) ............................................................................................................................................ 3,800
Dimensions (L x W x H) .....................................................................................................500 mm x 280 mm x 600 mm
Net weight ............................................................................................................................................................ 17.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for cutting in masonry and ferrous
materials with appropriate abrasive cut-off wheel.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1.
Wear hearing protection during extended peri-
ods of operation.
2.
Use only wheels having a maximum operating
speed at least as high as "No Load RPM"
marked on the tool's nameplate. Use only fiber-
glass-reinforced cut-off wheels.
3.
Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
4.
Secure the wheel carefully.
5.
Use only flanges specified for this tool.
6.
Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt, or the
wheel itself might break.
All manuals and user guides at all-guides.com
Explanation of general view
13 Stopper plate
14 Guide plate
15 Hex bolts
16 Vise plate
17 Vise nut
18 Vise handle
19 Spacer block
20 Straight piece of wood
(Spacer) vm
21 Over 190 mm long
22 Over 45 mm wide
23 Over 65 mm wide
24 Diameter of workpiece
25 Spacer block
26 Vise
27 Width of spacer block
28 Blocks
29 Switch trigger
30 Lock button/Lock-off button
31 Limit mark
32 Screwdriver
33 Brush holder cap
7.
Keep guards in place and in working order.
8.
Hold the handle firmly.
9.
Keep hands away from rotating parts.
10. Make sure the wheel is not contacting the work-
piece before the switch is turned on.
11. Before using the tool on an actual workpiece, let
it simply run for several minutes first. Watch for
flutter or excessive vibration that might be
caused by poor installation or a poorly balanced
wheel.
12. Watch out for flying sparks when operating.
They can cause injury or ignite combustible
materials.
13. Remove material or debris from the area that
might be ignited by sparks. Be sure that others
are not in the path of the sparks. Keep a proper,
charged fire extinguisher closely available.
14. Use the cutting edge of the wheel only. Never
use side surface.
15. If the wheel stops during the operation, makes
an odd noise or begins to vibrate, switch off the
tool immediately.
16. Always switch off and wait for the wheel to come
to a complete stop before removing, securing
workpiece, working vise, changing work posi-
tion, angle or the wheel itself.
17. Do not touch the workpiece immediately after
operation; it is extremely hot and could burn
your skin.
18. Store wheels in a dry location only.
SAVE THESE INSTRUCTIONS.
2414NB
5
Advertenties
Inhoudsopgave
