Download Inhoudsopgave Inhoud Print deze pagina

Replacing The Filter; Resetting The Filter; Moving And Storage; Troubleshooting - Bosch Air 6000 Installatie-Instructie

Inhoudsopgave

Advertenties

Beschikbare talen
  • NL

Beschikbare talen

  • DUTCH, pagina 75

Moving and storage

5.4

Replacing the filter

CAUTION
Wear a mask and gloves when cleaning the filter surface and/or replacing
the filter.
The air purifier is equipped with a filter replacement indicator
make sure that the air purification filter is in optimal condition when the
air purifier is operating.
Replace the filter as soon as possible.
NOTICE
The filter is not washable or reusable.
CAUTION
Always turn off the air purifier and unplug it from the electrical outlet
before replacing the filter.
▶ Switch off the air purifier and unplug it from the power socket.
▶ Pull the back cover and remove it from the appliance.
▶ Pull the filter from the appliance.
▶ Remove the plastic cover of the new filter [ Figure 6].
▶ Insert the new filter into the appliance.
▶ Reattach the cover.
▶ Insert the plug of the air purifier in the power socket.
▶ Touch the power button
▶ Touch and hold the filter status check/reset button
to reset the filter replacement counter.
▶ Wash your hands after replacing the filter.
Note:
Do not smell the filter as it has collected pollutants from the air.
5.5

Resetting the filter

When the filter lifetime counter reaches 0%, the screen displays the
message "Filter status 0%" reminding the user to replace the filter. The
message disappears when pressing the filter button
displayed again the next time the appliance is turned on.
[Figure 10 Message indicating the filter needs to be replaced]
The filter can be replaced before the filter lifetime warning is displayed.
The filter lifetime counter needs to be reset manually after its
replacement:
▶ Touch the power button
from the power socket.
▶ Insert the plug in the power socket.
▶ Long press the filter button
interface changes between the tree messages and then returns to the
original screen.
[Figure 11 Reseting filter messages]
To check the filter status, press the filter button
lifetime of the filter will be displayed and then returns to the previous
screen.
36
to switch on the appliance.
for 3 seconds
and will be
to turn off the appliance and unplug it
to reset the filter lifetime counter. The
. The remaining
6
Moving and storage
Moving
• Use two hands to hold the appliance when moving it.
Storage
to
▶ Turn off the air purifier and unplug it from the power socket.
▶ Clean the air purifier, the particle sensor and the surface of the filter
( Chapter 5 "Cleaning and maintenance", Page 35).
▶ Let all parts airdry before storing.
▶ Wrap the filter in air-tight plastic covers.
▶ Store the air purifier and the filter in a cool, dry location.
▶ Wash your hands after handling the filter.
7

Troubleshooting

This chapter summarizes the most common issues that may occur with
the appliance. If the solution is not found in the table below, please
contact an authorized service technician.
Problem
The airflow that comes out of the
air outlet is significantly weaker
than before.
The air quality does not improve,
even though the appliance has
been operating for a long time.
The color of the air quality light
always stays the same.
Possible solution
The surface of the filter is dirty.
Clean the surface of the filter
( Chapter 5 "Cleaning and
maintenance").
• Check if the plastic cover is
removed from the filter.
• The filter has not been placed in
the appliance. Make sure that
the filter is properly installed.
• The particle sensor is wet. The
humidity level in the room is
high and causes condensation.
Make sure that the particle
sensor is clean and dry
( Chapter 5 "Cleaning and
maintenance").
• Room size is large or the
outdoor air quality is poor. For
optimum purification
performance, close the doors
and windows when operating
the air purifier.
• There are indoor pollutants.
For example, smoking,
cooking, incense, perfume or
alcohol.
• Filter has reached the end of
life. Replace the filter with a
new one.
The particle sensor is dirty. Clean
the particle sensor ( Chapter 5
"Cleaning and maintenance"). If
the air quality is good, the light
should be blue at all times.
Air 6000 – 6721848696 (2023/07)

Advertenties

Inhoudsopgave
loading

Inhoudsopgave