Download Inhoudsopgave Inhoud Print deze pagina

Cleaning The Tool - Worx Nitro LeafJet WG585E Oorspronkelijke Gebruiksaanwijzing

Inhoudsopgave

Advertenties

Beschikbare talen
  • NL

Beschikbare talen

  • DUTCH, pagina 61
Air speed mode
NOTE: The blower is in the air speed mode for
default assembly.
NOTE: The blower has two working modes: air
speed mode and air volume mode. To change
modes, depress the nozzle release button
and slide backward for air speed mode. Slide
forward for air volume mode.
Choose a suitable mode according to your
work:
-
AIR SPEED MODE offers a high-speed,
concentrated airflow for sweeping
smaller areas, clearing debris out of
grass, or dislodging heavy or wet leaves.
-
AIR VOLUME MODE offers a high-volume
of mass airflow to cover a larger area or
on hard surfaces.
Air volume mode
OPERATION
Starting & Stopping
WARNING! The tool runs for a few
seconds after it has been switched off.
Let the motor come to a complete standstill
before setting the tool down.
Adjusting the blowing speed / air volume with
2-speed switch
USER TIPS
-
Hold the blower tube approximately 8"
above the ground when operating the
tool. Use a sweeping motion from side
to side.
-
After blowing the debris/leaves into a pile,
it is easy to dispose of the pile.
Caution!
-
Do not blow hard objects such as
nails, bolts, or rocks.
-
Do not operate the blower near
bystanders or pets.
-
Use extra care when cleaning debris
from stairs or other tight areas.
-
Wear safety goggles or other suitable
eye protection, long pants, and shoes.
Turbo button for power boosting
NOTE:
Turbo button for power boosting can
increase air flow significantly, and it
can be used for clearing heavy or wet
debris.
First switch on the blower and select
a speed control (speed I or II), then
depress the turbo button and hold it.
Release the Turbo button, the blower
will return to the previously selected
speed.
40V Cordless Blower
BATTERY STATUS (See Fig. D)
Before starting or after use, press the button beside
the power indicator light on the machine to check the
battery capacity.
During operation, the battery capacity will be indicated
automatically by the battery power indicator. The
indicator constantly senses and displays the battery
condition as follows.
For the machine with 2 battery packs with different
See Fig. E
power, the power indicator light displays the battery
condition with the lower one of the two batteries.
Battery
indicator light
status
Five green lights
(
See Fig.
illuminated.
F, G
Two, three or four
green lights are
illuminated.
See Fig. H
Only one green
light (
is illuminated.
No light is
illuminated.
Only one light is
flashing twice per
cycle.
See Fig.
I1, I2
Only one light is
flashing three
times per cycle.
Only one light
is flashing four
times per cycle.

CLEANING THE TOOL

Clean the tool regularly.
WARNING! Keep your product dry. Under no
circumstances spray with water.
See Fig. J
-
To clean the tool, use only mild soap and a damp
cloth.
-
Do not use any type of detergent, cleaner or
solvent which may contain chemicals that
could seriously damage the plastic.
-
Self lubricating bearings are used in your
product, therefore lubrication is not required.
Battery condition
The two batteries are in a highly
) are
charged condition.
The two batteries have a
remaining charge. The more lights
are illuminated, the more battery
capacity.
The battery level of at least one
)
battery pack is very low. Please
check and charge the battery pack.
At least one battery is not fully
installed or battery may be
defective.
At least one battery is over
discharged (please refer to the
battery charge condition), please
recharge the two batteries at once
before use again or storage.
At least one battery is hot, wait for
them cool down before start again.
The machine is over load. Remove
tool from blowing area and try
again.
13
EN

Advertenties

Inhoudsopgave
loading

Deze handleiding is ook geschikt voor:

Leafjet wg585e.xLeafjet wg585e. series

Inhoudsopgave