Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Read the complete manual before attempting installation and activating the system. Keep this
manual on hand for later reference.
1. DESCRIPTION
The 360° mini presence or mini absence detector for flush mounting consists of one unit with one-
channel on-off control, a motion sensor (PIR or passive infrared technology), a light sensor and an integrated
IR receiver. All external units, such as push buttons and lighting fixtures, are directly connected to the mini
detector, which is flush-mounted in the ceiling. The detector is for indoor use only and must never be installed
in environments with extreme temperature differences. Moisture may form inside the lens and reduce the
detection range.
The mini detector can be installed and operated on the basis of the factory settings. For optimal lighting
control, however, we recommend adjusting the factory settings to the specific conditions of the surroundings
and to the specific lighting requirements. The settings can only be adjusted using the IR remote control unit
(not included) (350-20090) or the Niko detector tool app and universal remote control for smartphones (not
included) (350-41936).
2. INSTALLATION
2.1. Connection
Danger: Disconnect all power before installing the mini detector. Do not connect the unit to the power supply
until installation has been completed.
Refer to the connection diagram (Fig. 1A).
To connect two mini detectors in parallel, consult Figure 1B (also see section 5.3.).
2.2. Mounting
Tip: Do not install the mini detector in the vicinity of heat sources, such as stoves or electric heaters, air
currents (ventilation systems) or moving objects (Fig. 2). This can activate the device unnecessarily, since
the device reacts to movement and heat.
Tip: The recommended mounting height is 2 to 3 m. The mini detector functions optimally at a height of 3
m. At this height, the mini detector has a detection range with a diameter of 9.5 m (Fig. 3).
The mini detector is suitable for direct flush-mounting in ceilings. Make an opening in the ceiling using a
hole diameter of 3 cm, and after connecting, insert the mini detector. Thanks to the spring terminals on the
mini detector, the device is easily fastened to the ceiling (fig. 4).
3. SETTINGS
3.1. Factory settings
Upon delivery, the parameters of the mini detector are set as follows:
Parameter
Factory setting
application
automatic on/off (presence detector), with the option to briefly press the
push button to:
• switch on the light and
• switch off the light without having to wait for the switch-off delay (=
eco-off).
Briefly pressing is daylight dependent.
light sensitivity
100 lux
switch-off delay
5 min
3.2. Applications
You can set up the mini detector:
• as a presence detector (automatic on/off): The mini detector automatically switches on the lighting,
depending on the set lux value and whether it detects motion.
• as an absence detector (manual on/automatic off): The mini detector switches the lighting on only if
you press the push button, depending on the set lux value.
After the last motion is detected, the lighting remains switched on for the duration of the preset switch-
off delay. As soon as the switch-off delay has elapsed, the lighting switches off.
If you connect a push button, you can immediately switch the lighting on as well as off without having
to wait for the switch-off delay by pressing the push button briefly (= eco-off). When switching off the
lighting using the push button, the mini detector is blocked for ten seconds to prevent the lighting from being
immediately switched on again. The 'eco-off' function is the most energy efficient manner to switch on the
lighting. You switch off the lighting yourself so that you do not have to wait for the switch-off delay. And if you
do forget to switch off the lighting, then this occurs automatically as soon as the switch-off delay elapses.
If you press the push button longer than one second, the red status LED will flash (0.25 s on and 5 s off). The
lighting is switched on or off as long as motion is detected, and the preset switch-off delay + 2 hours have not
yet elapsed. Pressing and holding is always daylight dependent.
Example: if the switch-off delay has been set to 5 minutes and you press the push button for more than 1
second, the switch-on or switch-off delay will be extended to 2 hours and 5 minutes.
If the push button has not been correctly activated or the mini detector has not properly received the signal
from the push button, the green and red status LEDs flash alternately (0.25 s on and 5 s off).
Consult section 5.4. for specific application examples.
3.3. Light sensitivity and switch-off delay
Using specific keys on the IR remote control unit (Fig. 5), you can set both the light level (light sensitivity)
at which the lighting must be switched on and the switch-off delay. You can choose from a number of fixed
lux and time values (see section 4.1.).
PM350-20085R24092
Lux
Lux
Lux
Lux
Pulse
2min
5min
10min
Time
8
15min
30min
60min
Hours
Memory
Memory
Clear
Status
The
button can be used to retrieve the settings of the mini detector. If the detector has been set to, for
in
out
memory
instance, 100 lux with a 5-minute switch-off delay, the green LED will flash once. Next, the red LED will flash
Test
Short
Long
Fact.
three times as an indication of the light level (100 lux), after which the green LED will flash.
On/Off
push
push
setting
Light level
20
Number of times
that the red status
LED flashes
Finally, the red LED will once again flash three times to indicate the switch-off delay.
Switch-off delay
Number of times that the
red status LED flashes
Please check section 4 to change the mini detector's settings
4. IR REMOTE CONTROL UNIT
You use the IR remote control unit (Fig. 5) to select another application, to perform a test or to enter other
parameters.
4.1. Settings keys
To change the mini detector settings:
1. Press
Lock/
three times within five seconds to unblock the device.
App.
unlock
Auto
20
50
The green status LED flashes twice by way of confirmation. The device is now in the settings mode.
Lux
Lux
300
2. Change the light level or the switch-off delay using the keys below. The red LED will flash to confirm that
Learn actual lux
Lux
the motion detector has received the signal from the remote control.
500
700
Lux
Lux
3. Press
Lock/
once to re-block the device.
App.
unlock
Auto
Pulse
2min
Time
20
50
The green status LED flashes twice by way of confirmation. The changed setting is activated, and the
Lux
Lux
15min
30min
device works again according to the newly selected settings.
300
Learn actual lux
Lux
Memory
Memory
in
out
Note: If you do not block the device, it will be blocked automatically after one minute. All changes are
500
700
then automatically saved.
Lux
Lux
Test
Short
On/Off
push
Key
Pulse
2min
Time
Lock/
App.
App.
Light
15min
30min
unlock
Auto
Active
On/Off
Lock/
App.
App.
Light
Memory
Memory
Lock/
App.
20
unlock
Lock/
App.
50
Light
Auto
App.
100
Active
App.
200
On/Off
Light
Lock/
App.
App.
Light
in
out
unlock
Auto
Lux
unlock
Lock/
Active
Lux
On/Off
Auto
App.
Lux
Active
App.
Lux
On/Off
Light
unlock
Auto
Active
On/Off
unlock
Auto
Active
On/Off
20
50
Test
100
Short
On/Off
push
Lux
Lux
Lux
20
20
300
50
50
100
100
20
200
200
50
400
100
Learn actual lux
Lux
Lux
Lux
Lux
Lux
20
Lux
Lux
50
Lux
100
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
300
Lock/
App.
App.
Learn actual lux
Light
Lux
300
500
300
700
1000
400
No
300
400
unlock
Auto
Active
On/Off
Learn actual lux
Learn actual lux
Learn actual lux
Lux
Lux
300
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Learn actual lux
Lux
500
700
1000
20
50
100
200
500
700
1000
Lux
500
700
Lux
No
1000
Lux
500
700
1000
No
Lux
Lux
Lux
Lux
Pulse
2min
5min
10min
Lux
Lux
Lux
Lux
500
Lux
Lux
700
1000
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Time
Pulse
2min
5min
10min
300
400
Learn actual lux
8
Pulse
15min
2min
Lux
30min
Pulse
5min
60min
10min
2min
5min
Lux
10min
Pulse
2min
5min
10min
Hours
Pulse
2min
5min
10min
Time
Time
Time
Time
Time
Lock/
App.
App.
Light
500
15min
700
30min
1000
60min
No
Hours
Memory
Memory
unlock
Clear
Auto
8
Active
On/Off
Lock/
App.
App.
8
Light
Lux
Lux
Lux
Lux
15min
30min
15min
60min
30min
Status
60min
15min
30min
60min
Hours
Hours
unlock
in
Auto
out
memory
Active
Hours
On/Off
15min
30min
60min
Hours
Memory
Memory
Clear
20
50
100
Status
Lock/
App.
App.
Light
Pulse
2min
in
5min
out
memory
10min
Memory
Memory
Test
20
Memory
Short
Clear
Lux
50
Memory
Long
Lux
100
Fact.
Clear
Lux
200
Memory
Memory
Clear
unlock
Auto
Active
On/Off
Status
Status
Status
in
On/Off
Lux
out
Memory
memory
push
Lux
in
Memory
push
Lux
out
setting
memory
Clear
Lux
in
out
memory
Status
in
out
memory
Time
Test
Short
Long
Fact.
300
8
20
50
100
200
Learn actual lux
15min
30min
60min
Test
Short
On/Off
Test
Long
Lux
Fact.
Short
push
Long
push
setting
Fact.
Test
Short
300
Long
Fact.
400
Hours
Lux
Lux
Lux
Lux
Learn actual lux
On/Off
push
On/Off
push
Test
setting
Short
push
Long
push
setting
Fact.
On/Off
push
Lux
push
setting
Lux
On/Off
push
push
setting
500
700
1000
Memory
Memory
Clear
300
400
Status
Learn actual lux
500
Lux
700
1000
Lux
No
Lux
in
out
memory
Lux
Lux
Lux
Lux
Lux
Lux
Test
Short
Pulse
Long
2min
5min
Fact.
10min
500
700
1000
No
On/Off
push
push
setting
Lux
Lux
Pulse
Lux
2min
Lux
5min
10min
Time
Time
15min
30min
60min
8
Hours
Pulse
2min
5min
10min
15min
30min
60min
Hours
Time
Lock/
App.
App.
Light
unlock
Auto
Active
On/Off
Memory
Memory
Clear
8
Status
15min
30min
Memory
60min
Memory
in
Clear
out
memory
Hours
Status
in
out
memory
20
50
100
Lux
Lux
Lux
Test
Short
Long
Fact.
Memory
Memory
Clear
On/Off
push
push
setting
Lock/
Test
Status
Short
App.
App.
Long
Light
Fact.
in
out
memory
On/Off
unlock
push
Auto
Active
push
setting
On/Off
300
Learn actual lux
Lux
Test
Short
Long
Fact.
20
50
100
200
On/Off
push
push
setting
Lux
Lux
Lux
Lux
500
700
1000
Lux
Lux
Lux
Lock/
App.
App.
Light
300
400
Learn actual lux
unlock
Auto
Active
On/Off
Lux
Lux
Pulse
2min
5min
10min
20
50
100
200
500
700
1000
No
Time
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
15min
30min
60min
Hours
300
400
Learn actual lux
Pulse
2min
5min
10min
Lux
Lux
Memory
Memory
Clear
Time
Status
in
out
memory
500
700
1000
No
8
15min
30min
60min
Lux
Lux
Lux
Lux
Hours
Test
Short
Long
Fact.
On/Off
push
push
setting
Pulse
Memory
2min
Memory
5min
10min
Clear
Status
in
out
memory
Time
8
Test
Short
Long
Fact.
15min
30min
60min
Hours
On/Off
push
push
setting
Memory
Memory
Clear
Status
in
out
memory
Test
Short
Long
Fact.
On/Off
push
push
setting
50
100
200
300
400
1
2
3
4
5
6
2 min
5 min
10 min
2
3
4
App.
Light
Active
On/Off
100
200
Lux
Lux
400
Lux
1000
No
Lux
Lux
App.
Light
Active
On/Off
5min
10min
100
200
Lux
Lux
8
60min
Hours
400
Lux
Clear
Status
memory
1000
No
Lux
Lux
Long
Fact.
push
setting
Function
5min
10min
Use this key to set the mini detector for use as a presence detector.
8
60min
Hours
Use this key to set the mini detector for use as an absence detector.
Clear
Status
memory
200
Long
Fact.
- Use these red keys to set the desired light level (lux value).
push
setting
Lux
200
Lux
200
Lux
- There are ten fixed lux values: 20, 50, 100, 200, 300, 400, 500, 700,
400
1000 lux and No lux (daylight dependent).
Lux
400
Lux
400
Lux
No
Lux
No
Lux
No
Lux
- Use this key to set the current light level in the room as the level at
which the lighting must be switched on.
- When you press this key, the red status LED flashes once to indicate
8
8
that the current light level has been loaded. If this light level is not
8
between 20 and 1500 lux, the minimum level (20 lux) or the maximum
200
level (1500 lux) is loaded.
Lux
400
Use this setting when the desired minimum light level in the room has
Lux
been reached. This is the time at which the lighting must be switched on
because the daylight level is no longer adequate.
No
Lux
- Use these blue keys to set the desired switch-off delay.
- There are six fixed values: 2, 5, 10, 15, 30 and 60 minutes.
8
If you press this key:
- The lighting remains switched on permanently for eight hours.
200
- The red status LED flashes (0.25 s on and 30 s
Lux
off).
- All other functions on the mini detector are blocked.
400
Lux
Press this key again to deactivate the function. The red status LED stops
No
Lux
flashing. The mini detector is returned to automatic mode. You can now
switch on the lighting again according to the selected application.
You cannot switch off this function using a push button.
8
With this button you can store the most recently selected settings (light
level and switch-off delay that were last set) into the memory of the IR
remote control.
Press this key to send the saved settings to the mini detector.
This key is handy for setting the same parameters on various mini
detectors simultaneously.
This key erases all settings from the memory of the IR remote
control unit.
350-20085
500
700
1000
∞
Learn
7
8
9
10
11
15 min
30 min
60 min
5
6
7
9
EN
Advertenties
Inhoudsopgave
