Advertenties
Beschikbare talen
Beschikbare talen
OBJ_BUCH-80-003.book Page 13 Wednesday, January 30, 2013 9:13 AM
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Helmut Heinzelmann
Senior Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
07.11.2007
Assembly
Before any work on the machine itself, pull the mains
plug.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suita-
ble for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Integrated Dust Extraction with Dust Box
(see figures G1 –G4)
Attach the dust box 4 onto the extraction outlet 12 until it
latches.
To empty the dust box 4, pull off the dust box downward.
Before opening the dust box 4, it is recommended to loosen
the dust from the filter element by gently striking it against a
firm support (as shown in the figure).
Grasp the dust box 4 by the recessed grip, fold the filter ele-
ment 13 upward and empty the dust box. Clean the thin
plates of the filter element 13 with a soft brush.
External Dust Extraction (see figure H)
Mount a vacuum hose 14 onto the extraction outlet 12. Con-
nect the vacuum hose 14 with a vacuum cleaner. An overview
for the connection of various vacuum cleaners can be found at
the end of these instructions.
Bosch Power Tools
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Replacing the Sanding Sheet
When attaching a new sanding sheet, remove any dust or de-
bris from the sanding plate 6 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Sanding Sheets with Velcro Backing (see figure A)
The sanding plate 6 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 7, free the Velcro backing
of the sanding plate 6 from any debris by tapping against it in
order to enable optimum adhesion.
Position the sanding sheet 7 flush alongside one edge of the
sanding plate 6, then lay the sanding sheet onto the sanding
plate and press firmly.
To remove the sanding sheet 7, grasp it at one of the tips and
pull it off from the sanding plate 6.
Sanding Sheets without Velcro Backing (see figures B–D)
Press the release button 8 and keep it depressed.
Guide the sanding sheet 7 to the stop under the opened
front clamping bracket 9 and let go of the release button
8 again. Pay attention that the sanding sheet is clamped
centrally.
Press the sanding sheet clamp 5 inward and pivot it to
the stop.
Fold the sanding sheet 7 firmly around the sanding plate.
Guide the other end of the sanding sheet 7 between the
rear clamping bracket and the red roller on the clamping
bracket 5.
Hold the sanding sheet tensely and press the clamping
bracket 5 toward the sanding plate to lock the sanding
sheet.
Sanding sheets without holes, e. g. from rolls or by the meter,
can be punctured with the perforating tool 10 for use with
dust extraction. For this, press the machine with the mounted
sanding sheet onto the perforating tool (see figure E).
To remove the sanding sheet 7, loosen the clamping
bracket 5 and pull out the sanding sheet from the rear holding
fixture. Press the release button 8 and completely remove the
sanding sheet.
English | 13
2 609 141 028 | (30.1.13)
Advertenties
