Advertenties
Beschikbare talen
Beschikbare talen
∙ Caution! Whenever the barbecue is not in use, the
heating element with the connection box must be
removed from the barbecue and stored in a dry
space indoors.
∙ The other parts of the barbecue must not be stored
outdoors or in an open area where they could be
affected by the weather.
∙ The grill may only be used with the supplied core
thermometer or the SEVERIN item no. ZB 8126.
∙ No responsibility is accepted if damage results from
improper use, or if these instructions are not complied
with.
∙ This product complies with all binding CE labelling
directives.
Before using for the first time
∙ Remove any packaging materials and stickers from the
appliance.
∙ C lean the grill rack, reflector tray and the tray inserts
with warm soapy water; wipe thoroughly dry afterwards.
∙ Assemble the appliance as described in Preparing the
unit.
∙ Let the grill heat up for approximately 10 minutes at
maximum power without any food (see 'Boost-zone'
grilling). This will remove the smell typically encountered
when first switching on a grill. A little smoke may be
emitted; for that reason, adequate ventilation should
be ensured by opening windows or balcony doors; an
extractor hood is also suitable.
Grill assembly
∙ Assemble the grill as shown in the diagrams:
∙ Place the reflector tray into the grill housing.
∙ Note: Fit the tray inserts so that each insert covers
four protrusions.
∙ Fit the heating element with junction box into the
reflector tray. The appliance is equipped with a safety
switch. The unit can be operated only with the junction
box properly installed.
∙ Fit both grill rack elements so that the studs on the
rack fit into the corresponding openings in the reflector
tray.
12
Grill cart assembly
∙ For grill models with grill cart, assemble the cart as
shown in the diagram.
∙ For assembly, a Phillips screwdriver is needed.
∙ Prior to assembly, check that all parts are complete as
listed in the Familiarisation section.
∙ Assembly:
∙ Place the grill cart frame upside-down on the floor.
∙ Insert the four support legs into the housing and
secure each support leg with two big bolts. The two
support legs with the additional holes for the wheels
must be mounted together on the narrow side of the
grill cart.
∙ Turn the frame with the support legs upright.
∙ Fit the plastic frame of the storage rack and secure it
on all four support legs, using the corresponding bolts
and nuts; then fit the storage rack.
∙ Slide the wheel axles through the openings on the
support legs and put on the wheels. Secure each
wheel with one of the cotter pins and clip on the wheel
covers.
∙ Fit the side tables onto the corresponding metal pins.
∙ Ensure that the grill cart is stable. Check the bolts
regularly for firm connection.
∙ Place the assembled grill on top.
Caution:
∙ Do not exceed a maximum load of 3 kg for the side
tables, and 20 kg for the storage rack.
∙ If you need to move the grill, remove the table on the
side opposite from the wheels and grip the frame.
Preparing the unit
∙ Assemble the appliance as described in Grill assembly.
For grill models with grill cart, refer to Grill cart
assembly.
∙ F ill the reflector tray with water to the Max marking (max
2 litres). Do not pour water on the heating element or its
sensor.
Hint!
During grilling, the water in the reflector tray should be
replenished in good time. Caution: Always disconnect
the appliance from the mains before re-filling.
∙ Connect the appliance to the mains.
∙ The light ring lights up blue, the unit is ready for use.
Rotary control
The rotary control is used for function selection or switching
off (Sleep mode).
Turn:
Select the Function/Temperature/Timer.
Push - short:
Confirm the selection.
Push - two seconds:
1 x: return to stand-by mode to change a function
2 x: return to sleep mode
Advertenties
