Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
G Operating Instructions
Radio-controlled switch set, 2 parts
Item no. 1208455
Intended Use
The product consists of a radio controlled main socket and a radio controlled hand-
held transmitter. By using the hand-held transmitter, consumer loads connected to the
remote controlled switch socket can be turned on or off.
All safety and operating instructions in this manual must be followed carefully. These
instructions not only protect the device but, in particular, your well-being. Please read
the entire operating manual before using the product.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package contents
• 1x radio controlled main socket
• Hand-held radio transmitter
• 12 V special battery for hand-held radio transmitter
• Operating instructions
Safety Instructions
D amages due to failure to follow these operating instructions will void the
warranty/guarantee! We do not assume any liability for any resulting dam-
age!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty/guarantee will be null and void!
• The unauthorized opening, conversion and/or modification of this product
is not permitted for safety and approval reasons (CE).
• Do not use this product in hospitals or medical institutions. Although the
product only emits relatively weak radio signals, these may lead to the
malfunction of life-support systems. The same may also apply to other
zones.
• The radio-controlled switch socket(s) is/are designed in accordance with
protection class I. Only (a) standard mains socket(s) (230V~/50Hz with pro-
tective earth) for the public supply grid may be used as the power source
for the radio-controlled switch socket.
• The hand-held radio transmitter is powered by a 12 V battery (type "23A").
• The product is not a toy and does not belong in the hands of children!
Therefore, be especially careful when children are around. Children might
try to push objects through the socket openings, for example. There is
danger of a life-threatening electric shock!
• The product must only be used in dry interiors, it must not get damp or wet.
Never touch the product, or the mains plug, with wet or damp hands when
trying to connect a plug to the wireless switch socket.
There is danger of a life-threatening electric shock!
• Never remove a mains plug from the radio controlled mains socket by pull-
ing the power cable. Always pull the plug from the socket, in the radio-
controlled switch socket, using the gripping surface provided on the side.
• Do not connect adaptor plugs in series!
• The device is only voltage-free when iit is disconnected from the mains
socket.
• Do not overload the radio switch socket (take note of the input power in
the technical information at the end of the operating manual!).
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or
accidental falls, even from a low height.
All manuals and user guides at all-guides.com
Controls
A
B
A Control-LED (lights up on use of buttons)
B Keypad for switching channels 1 to 4 (left column "ON" = on, right column "OFF" = off)
C Coding switch I, II, III, IV for one of the four address codes
D Battery compartment for a 12 V battery of type "23A"
E Control-LED (lights up when the mains socket on the front is activated)
F Front socket for connecting of a consumer load, with child-proof lock
G Coding switch I, II, III, IV for one of the four address codes
H Coding switch for switch channel selection 1, 2, 3, 4
I
Inserting/replacing the Battery
Open the battery compartment (D) on the back of the hand-held radio transmitter and
insert a 12V-battery (type "23A") with the correct polarity (observe imprint in the bat-
tery compartment or the figure). Close the battery compartment again.
The batteries need to be replaced if the range of the hand-held radio transmitter is sig-
nificantly reduced or the control-LED (A) no longer lights when the buttons are used.
Setting the Address Codes
One of the four address codes (I, II, III, IV) can be set on both the hand-held radio
transmitter and the radio-controlled switch socket. Therefore, up to four identical
radio-controlled switch sets can be operated without influencing each other.
Select one of the address codes (I, II, III, IV) on the hand-held radio transmitter via the
sliding switch (C). Set exactly the same address code on the related radio-controlled
switch socket(s); use a flat screwdriver for turning the coding switch (G).
Setting the Switching Channel of the Radio-Controlled
Switch Socket
On the back of the radio-controlled switch socket there is a further coding switch (H)
that is marked by the numbers "1", "2", "3" and "4". It is used to select one of the four
switching channels (the hand-held radio transmitter has also imprinted the number
"1", "2", "3" and "4") if more than one radio controlled switch socket is operated.
Start-up, Function Test
Plug the radio-controlled switch socket (without the consumer load connected!) into
the designated earthed mains socket.
You can now test the function of the radio-controlled switch socket, by briefly pressing
the respective "ON" button for the corresponding switching channel (1, 2, 3 or 4). The
red control-LED (E) on the radio-controlled switch socket lights up. The mains socket
(F) on the front is now activated; mains voltage is available and a connected consumer
load is turned on.
Briefly press the "OFF" button of the switching channel and the control-LED (E) is
turned off; mains voltage at the mains socket (F) and therefore the connected con-
sumer load is turned off.
• If the product casing is damaged, discontinue product usage! When it is
still connected to the mains, do not touch the radio switch socket or the
connected device! First, switch off the mains socket to which the radio
switch socket is connected (switch off at the circuit breaker). Only then
can you remove the radio-controlled switch socket from the mains socket.
Take the product to a specialist workshop or dispose of it in an environ-
mentally friendly way.
1
2
3
4
ON
OFF
C
D
-
+
Safety plug for connection to the mains socket
If you set a different code on the hand-held radio transmitter and the radio-
controlled switch socket, the switch socket will not react to the switching
commands on the hand-held radio transmitter!
It is of course possible to set the same switching channel for two or more
radio controlled switch sockets. By means of this, the two radio-controlled
switch sockets are activated or deactivated by one keystroke.
E
F
G
H
I
Advertenties
Inhoudsopgave
