Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
UK: INSTRUCTION MANUAL
Connecting your appliance to a gas cartridge
To be able to use your appliance you will need to purchase a gas cartridge which is suitable for this
specific appliance. Please see TECHNICAL DATA table for information regarding the gas cartridge.
1) Position the gas cartridge at the side of your appliance, keeping in mind that the cartridge must be
kept away from heat and in a safe and upright position.
2) Make sure that the tap on the adaptor (6) is fully closed by turning it clockwise towards symbol "–".
3) Make sure that the individually controlled knob(s) (2) are closed by turning them fully clockwise
towards the small "symbol "•".
4) Carefully screw the gas cartridge onto the adaptor (6) taking care not to cross thread. Screw down
until the sealing washer meets the cartridge (hand-tight only).
5) Always check for leaks at all joints before lighting the appliance.
6) Never leave the adaptor (6) attached to the gas cartridge if the hose (4) with connector (5) is
disconnected from the appliance.
Lighting Your Gas Appliance
1) Make sure your gas appliance is assembled and gas cartridge connected according to above
instructions.
2) Open the tap on the adaptor (6) by screwing the tap counterclockwise towards the "+" symbol.
3) Open the individually controlled burner knob(s) (2), depending on which burner you want to use, by
screwing the knob(s) counterclockwise away from the small "•" symbol.
4) Hold a lighter or match near the burner(s) to ignite.
5) When the burner is lit, turn the control knob(s) (2) clockwise to decrease the heat intensity or
extinguish, and counterclockwise to increase.
6) Do not open valves beyond the point where maximum intensity is reached as this may cause
unnecessary flaring and waste gas.
7) Do not move the appliance or gas cartridge once lit as this may result in flaring. A warm-up period of
about 1 minute is required to avoid flaring.
8) If you experience flaring (high yellow flames), turn down the control knob (2) (towards the "•" symbol)
until the flames are controlled and blue. Wait a few seconds and slowly increase the flame again.
9) Avoid twisting of the flexible hose.
10) If the gas pressure drops or the gas will not light, check if there is still gas left in the cartridge. If there
is gas left in the cartridge the gas temperature may be too low.
For your safety – if you smell gas
•
If there is a leak on your appliance (smell of gas), take it outside immediately into a well- ventilated
flame free location where the leak may be detected and stopped. If you wish to check for leaks on
your appliance, do it outside. Do not try to detect leaks using a flame, use soapy water.
•
If odour persists, contact the dealer or Outwell Customer Service (contact details below) and stop
using the appliance immediately.
3. CHANGING OR DISCONNECTING GAS CARTRIDGE
•
Only disconnect the gas cartridge when the appliance is not being used.
•
The cartridge can be disconnected/reconnected even if some gas remains.
•
Make sure to turn off the appliance completely by screwing the tap on the regulator (6) fully
clockwise towards the symbol "-" and the knob(s) fully clockwise towards the symbol "•". Be careful
the appliance could be hot.
•
The gas cartridge shall be changed in a well-ventilated location, preferably outside, away from any
sources of ignition, such as naked flames, pilots, electric fires and away from other people.
•
Carefully unscrew the gas cartridge from the adaptor (6).
•
Check the contents of a cartridge by shaking it and listening for the sound of liquid gas.
•
Dispose of as per instructions printed on the cartridge.
•
To ensure a safe connection of a new gas cartridge to your appliance please read the sections
'ASSEMBLY' and 'OPERATION' .
4
UK: INSTRUCTION MANUAL
4. CLEANING & MAINTENANCE
•
Visually check the general condition of the appliance and clean it on a regular basis.
•
Ensure the appliance has cooled off completely before cleaning.
•
Use a wire brush, steel wool or a scouring pad to clean the pot/pan holder(s)(1).
•
Interior surfaces of the appliance housing cover should also be washed with hot soapy water.
•
Check the burner(s) regularly to see that it is free from insects and spiders which may block the gas
system.
•
Check the seals regularly to ensure that they are in good condition. If there is any sign of wear and
tear the seals must be replaced with new ones. Contact the dealer or Outwell Customer Service
(contact details below).
•
Check and clean the injectors on the appliance if they are blocked.
Injectors
5. CLEANING THE INJECTORS:
•
Fully turn off the control knob(s) (2) and disconnect the gas cylinder
•
Remove the pot/pan holders (1)
•
Turn the appliance upside down and loosen the base of the burner
•
Blow compressed air through the hole to clean the injector
•
Reassemble the base of the burner
•
Place the pot/pan holder(s) (1) back into the molded holes.
•
Reconnect the gas cylinder. Check the connecting joint with warm soapy water.
5
Advertenties
Inhoudsopgave
