Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Contents
1.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.
Fitting the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.
Access Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1 Setting access options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 Setting INDIVIDUAL access options (2-9 Cats) . . . . . . . . . . . . . . . . . . . . 6
4.3 Setting timer control / lock for ALL cats . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.
Fitting I.D. Disc(s) to Your Cat(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.
Viewing your cat(s) location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.
To view how long since the cat(s) last used the cat flap . . . . . . . . . . . . . . . . . . 8
8.
if Your Cat Has Lost its I.D. Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
9.
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10. Reprogramming a New I.D. Disc or Microchipped Cat . . . . . . . . . . . . . . . . . . . 9
11. Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
12. Energy Saving Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
13. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1. Introduction
Thank you for choosing the Cat Mate Elite Cat Flap with Timer Control.
CAREFULLY READ THESE INSTRUCTIONS AND PROGRAM / TEST THE CAT
FLAP BEFORE YOU INSTALL IT.
The Cat Mate Elite Cat Flap with Timer Control allows you to control up to 9 cats to
have access to and from your property. Furthermore, it will allow you to monitor the
movement of up to 3 individual cats: showing when your cat last entered or left the
house, and how many hours since your cat last used the flap.
4
To ensure that your chosen settings cannot easily be tampered with, we have made
If you wish to stop any task (except programming) at any stage, the system will time
the control buttons so that they need to be pressed firmly to operate.
out after 60 seconds.
Settings will not be saved unless you press the 'SET' button.
The Microchip Cat Flap with Timer Control (Ref. 355) is suitable for all popular
microchips. Alternatively it may be operated by an I.D. Disc (available separately).
You may wish to use an I.D. Disc for cats without a microchip or in the event that
your cat's microchip is faulty or poorly positioned.
2. Fitting the Batteries
2.1 Remove the battery cover by pushing the battery cover upwards (see Fig. 2).
The cover will snap off.
2.2 Insert 4 x AA (R6) batteries as shown (Fig. 3), by sliding the 2 end batteries
in first.
2.3 The cat flap will self-check for up to 60 seconds after which only the 'IN & OUT'
arrows will be visible on the LCD display. The flap is ready to program.
You may use all popular batteries including rechargeable and lithium batteries but
the 'BATTERY INDICATOR' will only work correctly with alkaline batteries. Good
quality alkaline batteries should last approximately 12 months (depending on
number of cats and usage).
3. Programming
The next step is to program the microchip or I.D. Disc belonging to each cat. We
recommend that you now choose a number for your cat(s) and, if appropriate, mark
it on the I.D. Disc label and on the table at the end of these instructions.
NOTE: The programming sequence is time sensitive and the LCD will revert to the
In order for the flap to recognise your cat(s) microchip or I.D. Disc, you need to do
normal display if each step is not completed within approximately 15 minutes.
the following:
3.1 Press and hold the 'PROGRAM' button on the circuit board for 5 seconds
(Fig. 4) until the search indicator (Fig. 1) appears.
3.2 'CAT 1' and the number '1' will flash - there will be lines moving around the first
'TWO ZEROS'.
3.3 Place the front of the I.D. Disc in the tunnel opening (Fig. 5) or to program your
cat's microchip, encourage your cat to slowly pass through the tunnel by
holding the flap open as shown in Fig. 6.
3.4 When programmed, the 'TWO ZEROS' will disappear and 'Pr1' will flash.
3.5 Press the 'SET' button to save the setting.
For additional cats, up to a maximum of 9, repeat steps 3.1 to 3.5.
5
Advertenties
Hoofdstukken
Inhoudsopgave
Probleemoplossen
