Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Mounting and adjusting the mitre fence (fig. I)
The max. mitre angle is 60° .
Slide the mitre fence (5) into the slot (34) to
■
the left or right of the table (4) as required.
Loosen the adjustment screw (35).
■
Set the desired mitre angle using the scale on
■
the protractor (36).
Tighten the adjustment screw.
■
Instructions for use
Firmly hold the workpiece while sanding.
■
Do not exert extra pressure.
Start with a coarse grain and slowly switch to
■
a finer grain to produce the best result.
Use the mitre fence for extremely precise work.
■
Using the sanding disc (fig. A)
Use the sanding disc for sanding rough wood
■
ends.
Press the workpiece against the sanding disc.
■
Move the workpiece back and forth along the
■
disc until you have reached the desired result.
Using the sanding belt (fig. A)
When using the machine in the horizontal
■
position, place the workpiece against the
fence on the sanding belt.
When using the machine in the vertical
■
position, place the workpiece on the table
against the sanding belt.
Move the workpiece back and forth over or
■
against the sanding belt.
Always sand wooden workpieces in the
■
longitudinal direction of the grain.
Switching on and off (fig. A)
To switch the machine on, set the on/off
■
switch (1) to 'I'.
To switch the machine off, set the on/off
■
switch (1) to '0'.
Never use the machine for
sanding magnesium workpieces.
Readjusting the bumper cushion (fig. J)
The bumper cushion (37) should be readjusted
when the sanding belt arm (2) is not level.
Turn the bumper cushion in or out to
■
determine the correct adjustment.
Check that the sanding belt arm is level.
■
Dust extraction (fig. E)
The dust extraction connection (38 & 39) together
with an external vacuum cleaner takes care of the
dust extraction of the working surface.
Slide the suction mouth of a vacuum cleaner
■
onto the connection (38 & 39).
CLEANING
Before performing any work
on the equipment, pull the
GB
power plug.
Cleaning
§ Regularly clean the machine housing with a soft
cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt. If the dirt
does not come off use a soft cloth
moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water,
etc. These solvents may damage the plastic parts.
Lubrication
The machine requires no additional lubrication.
TECHNICAL DATA
Mains voltage V
Mains frequency Hz
Power input W
-1
Engine speed min
-1
No-load speed min
Sanding belt dimensions mm
Sanding disc diameter mm
Table dimensions mm
Weight kg
Noise emission values measured according to
relevant standard.
Acoustic pressure level
LpA 72.39 dB(A) K = 3 dB(A)
Acoustic power level
LwA 85.39 dB(A) K = 3dB(A)
The sound power pressure may
exceed 85 dB(A), in this case
individual hearing protection
Weighted root mean square acceleration according
to relevant standard. : < 2.5 m/s²
The declared vibration total value has
been measured in accordance with a standard
test method and may be used for comparing one
tool with another that the declared vibration total
value may also be used in a preliminary
assessment of exposure.
A warning that the vibration emission
during actual use of the power tool can differ
from the declared total value depending on the
ways in which the tool is used and of the need to
identify safety measures to protect the operator
that are based on an estimation of exposure in
the actual conditions of use (taking account of
all parts of the operating cycle such as the times
when the tool is switched off and when it is
running idle in addition to the trigger time).
230
50
500
2800
7.6m/sec
100 x 914
152
158 x 225
22.45
ATTENTION !
must be worn.
22
Advertenties
Inhoudsopgave
