Advertenties
WIRED CONTROLLER
A
SPECIFICATIONS
- Supports Nintendo Switch, PC D-INPUT and PC
X-INPUT platforms
- Two 3D analog joysticks with lifetime over 1 million
clicks
- Dual vibration with strength adjustment function
- Buttons lifetime over 800 thousand clicks
- Cable length 3m
Screenshot
Left
Command
A/B/X/Y
joystick
- button
+ button
button
buttons
LED
channel
Right
D-pad
indicator Menu
joystick
Note: Vertical press on the left joystick is L3; Vertical press on the right joystick is R3; Channel indicators are LED1, LED2,
LED3, LED4 from top to bottom.
2
- This controller does not have six axis sensors, and
does not support motion mode.
- Two rear combo buttons to program up to 16
combination actions from 14 buttons
- Turbo mode available on 12 buttons with turbo
speed adjustment function
ZR
R
L
ZL
trigger
trigger
trigger
trigger
BR
Reset
BL
trigger
trigger
OPERATING INSTRUCTIONS
Attention: Before using the controller for the first time, ac-
tivate the «wired communication» option in the console
menu.
• Turn on Switch console and enter the main interface.
• Select "System Settings", then "Controllers and Sensors".
• Set "Pro Controller Wired Communication" to "ON".
Connection with the Switch Dock
• Turn on the Switch console and enter the main interface.
• Connect the Switch with the TV through the Dock and
output the video to the TV.
• Connect the controller's USB connector to the Dock's
USB port, press button A to confirm. When the controller
is successfully connected, a channel will be automatically
allocated, and the corresponding LED indicator will light
in solid white.
Connection with a PC
• When connected to the PC for the first time, the default
is X-INPUT simulation mode.
• Press the HOME button for 5s to shift between X-INPUT
& D-INPUT modes. The mode is kept in memory.
• Short press the HOME button to shift between PC
D-INPUT simulation mode and PC D-INPUT digital mode.
LED light indicator on PC:
• PC X-INPUT mode:
• PC D-INPUT (simulation mode):
• PC D-INPUT (digital mode):
Vibration strength setup
Default is set at 50% strength
• Press COMMAND and tilt the left joystick up to set to
70%, and tilt again to 100%
• Press COMMAND and tilt the left joystick down to set to
30%, and tilt again to 0%
Special functions setup instructions
You can press "+", "-" and "COMMAND" at the same time
5s to reset all the settings.
In Turbo/Combo setup mode, no operation within 30s or
any wrong operation will exit setup mode without saving
the setting.
Turbo function setup
12 buttons can be mapped as Turbo: Up, Down, Left, Right,
A, B, X, Y, R, L, ZR, ZL
• To set a Turbo function, press and hold the button you
want to set as Turbo, and at the same time press COM-
MAND "C" button. The button set as Turbo will automati-
cally operate when being pressed.
• Press the button you set as Turbo and COMMAND at the
same time again to cancel the Turbo function on this but-
ton.
• Multiple buttons can be set as Turbo at the same time.
Turbo speed setup:
Default is 12 presses/second
• Press COMMAND and tilt the right joystick up will set to
20 presses/second
• Press COMMAND and tilt the right joystick down will set
to 5 presses/second
• The Turbo speed setup is kept in memory.
Combo shortcuts mapping
2 buttons can be set as combo shortcuts: BL, BR. 14 but-
tons can be mapped in a combo: Up, Down, Left, Right, A,
B, X, Y, R, L, ZR, ZL, L3, R3. The default mapping of BL and
BR is A and B.
• Pressing BL and BR buttons at the same time will only
activate the button pressed first.
Combo shortcuts setup method:
• Press COMMAND and BL/BR at the same time, BL/BR will
enter combo mode and LED1 will flash quickly in orange.
• Press any button listed above that you want to map as a
combo, the time between the button presses will also be
recorded. When 1 button has been pressed, the indicator
A
3
Advertenties
