Advertenties
Beschikbare talen
Beschikbare talen
GB
Vetec DUAL 30.1+50.1 Hybride class III User manual
Safety instructions:
Before use first read safety instructions. Use the floodlight only for
the purpose it is designed for: as a lamp for illumination in dark
areas in -outdoors. Any other use of the lamp can cause damage
to the lamp or cause hazard to the user and its environment, such
as electrical shocks, fire and short circuit. This operation manual is
part of the product. Provide this document when selling the product
to the new owner.
• Do not use the floodlight near any flammable substances or
gases.
• Use only the included accessories.
• Keep the lamp out of reach of unauthorized persons, especially
children.
• Do not shine the light in the eyes of people and animals.
• Always check the charging/power cable and AC adapter/charger
before using the floodlight.
• Do not use this product if any part is damaged or defective.
If the product is damaged or defective, replace the product
immediately.
• Do not modify the product in any way.
- Do not expose the product to water or moisture (IP20).
- Do not immerge the product into water. (IP44 - IP67
- Keep the product away from heat sources.
- Do not block the ventilation openings.
- Do not look directly into the LED lamp.
- Keep a minimum distance of 1 meter between the lamp and the
surface being illuminated.
Electrical safety
• To reduce risk of electric shock, this product should only be
opened by an authorized technician when service is required.
• Do not use the product if the cable or plug is damaged or
defective. When damaged or defective, it must be replaced by the
manufacturer or an authorised repair agent.
• Before use, always make sure that the voltage is the same as the
voltage on the rating plate of the device.
• Make sure that the cable does not hang over the edge of a
worktop and cannot be caught accidentally or tripped over.
Cleaning instructions
• Remove the charging/power cable before cleaning the LED
floodlight and let the floodlight cool down.
• It is enough to clean the LED spotlight with a dry or slightly damp,
clean, nonfluffy cloth. If necessary, use a mild detergent. Do not
use detergents containing abrasives or solvents.
Maintenance
• Before use, please check the plug, charging / power cord, AC
adapter/charger and case of the product for damage. If the LED
panel (lens) is damaged, it must be replaced immediately.
• Clean contamination on the housing or lens, as this may lead to
overheating.
• If you do not use the battery for a long period of time, it should be
charged at least every 3 months to avoid complete discharge and
maintain service life.
Use of the LED Floodlight
Image 1
1. Attach the foot to the standard with the fixing screw.
2. Connect the reversed polarity protected connector (2 pins) of the
charging / power cord to the AC adapter/charger and screw it to
the wartel nut.
3. Connect the other end (DC plug) to the LED floodlight and
wartel nut. Make sure that the wartel nut is properly connected,
otherwise the prevention of water penetration will not be
guaranteed.
Warning! Danger of blinding! When in use with the AC
adapter/charger, without the optional battery, the LED
floodlight will turn on immediately.
Image 2
Unscrew the side screws to adjust the LED spotlight vertically.
Retighten the side screws after adjustment.
Image 3
The standard integrated magnet ensures that the LED spotlight can
be placed on any magnetic surface.
Use of the LED floodlight with battery (Image 4/5/6)
• Remove the charge/power cable (if connected).
• Place the battery on the back of the LED spotlight and fasten it
with the two quick fasteners
To charge, connect the cable with the charging socket (Image 6C)
under the transparent cover. During charging, the battery light
flashes. When all 4 LEDs are lit, charging is complete and the
charge/power cable can be removed.
Mode 1 - Lamp powered by Battery
During operation with the battery, the LED floodlight can be turned
on and off with the yellow switch (Image 6B) and dims to 50% with
the yellow switch (Image 6A).
Mode 2 - lamp powered by mains-power
Attention! When the LED floodlight is used with attached battery
Together with the AC adapter / charger, it has only IP20 (dry
spaces). To Turn lamp on, press the yellow button (Image 6B). The
LED charging indicator (Image 6E) goes out. Dim-function (Yellow
switch, Image 6A) is not possible in this mode and the USB (Image
6D) is disconnected.
Image 6
A: 50% / 100% intensity selector switch
B: On / Off switch
C: DC Input (Charging)
D: USB output (for example, charging
mobile phones)
E: Battery life indicator
Advertenties
