Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ENG_5
User Instructions
General Instructions all Models
Inspect the Ladder after delivery. Before every use visually check the Ladder is not damaged and is safe to use.
Do not use a damaged Ladder.
Do not exceed the Maximum rated load
Ensure the ground or floor surface is firm and acceptably level before use
Do not overreach - Keep your centre of gravity within the platform area
Ensure the ground or floor surface is free form oils or spills - Do not use on contaminated ground
Maximum number of users is limited to 1 at any given time
Face the Ladder when ascending and descending - Do not ascend or descend with your back to the steps
Keep a secure grip on the Ladder when ascending or descending. Maintain a handhold whilst working from a
ladder or take additional safety precautions if you cannot
Avoid work that imposes a sideways load on Ladders, such as side on drilling through solid materials
Do not carry equipment which is heavy or difficult to handle while using a Ladder
Do not wear unsuitable footwear - Wear slip resistant footwear
Do not use the Ladder if you are not fit enough. Certain medical conditions or medication, alcohol or drug
abuse could make Ladder use unsafe
Do not spend long periods on a Ladder without regular breaks - Tiredness is a risk
Prevent damage of the Ladder when transporting by fastening and ensuring the Ladder is suitably positioned
Ensure the height of the Ladder is suitable for the task
Do not use the Ladder if contaminated - Keep Ladder treads and platform clean and free from grease and oils
Do not use outside in adverse conditions such as strong winds and heavy rain
A risk assessment must be carried out prior to use respecting the legislation in the country of use
When positioning the Ladder for use. Take into account the risk of collision with the Ladder - Do not place
the Ladder where the risk of collision with vehicles, pedestrians or doors may occur. Do not place the Ladder
within 1 meter of stairwells, loading docks or similar situations without positively anchoring the Ladder to the
building or other suitable fixture
Do not use where Electrical hazard exists - Identify any electrical risks such as overhead power-lines or other
exposed electrical equipment.
Use Non-conductive ladders for unavoidable live electrical work
Do not use the Ladder as a bridge
Do not modify the Ladder design
Do not move a Ladder while standing on it - Do not use the Ladder to move persons
For outdoor use - Caution to the wind
Do not climb above the platform
Do not step off the side of the ladder onto another surface or structure
Keep both feet within the platform area
Do not leave loose tools on the platform area
www.stockmastereurope.nl
ENG_6
Assembly
G
eneral Assembly:
Instructions for assembly are provided in graphic form. These must be followed to ensure correct assembly and
safe working of the product. They also provide the most simple method for assembly. If you are unsure of any of
the instructions, please consult your dealer.
Note: Any defect arising as a result of incorrect assembly will not be covered under your product warranty.
P
latform Safety Rail Assembly: (Navigator, Tracker and Lift-Truk)
The Platform is supplied with two sets of Side Safety Rails, a High Rail set and a Low Rail set. For safety and
productivity, the selection will depend on the nature of use. The Platform may be assembled in any combination
of;
2 x High Rails - Recommended where the Ladder is to be used in open space or for working overhead.
2 x Low Rails - Recommended where the Ladder is to be used in a confined space such as narrow aisle of racking
where the width of the Ladder approximates the width of the aisle, and maximum side access is required.
1 x High and 1 x Low Rail - Recommended where the operator works to a single work-face where maximum side
access is required and there is open space behind. An example of this situation is order picking in wide aisles or
machinery maintenance.
Inspection and Initial Testing
O
n completion of the assembly and BEFORE USING, do the following
A
ll Models;
Check that all fastenings have been tightened.
Place the Stockmaster on a flat surface and check that all 4 x supporting points of the unit are in contact with
the ground
Check that when in the stationary mode, the control handle returns to the rest position
N
L
avigator and
ift -Truk Models;
Check all 4 x castor's retract in the stationary mode
L
ift -Truk Models;
Bring the Lift Table to the lowest position. Place a load of 5kg on the Lift Table and raise it approximately
0.3 meter. Check that when the winch handle is released the load does not move. Repeat the test at the rated load
of 60kg. IF THE LOAD MOVES, DO NOT USE THE LIFT TABLE and consult your Stockmaster dealer.
Back
www.stockmastereurope.nl
User Instructions
Back
Advertenties
Inhoudsopgave
