Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
MANUAL - QUARTOO
2.4.2 Monobloc
1
2
Place the installation in the final position;
Attach the pump to the pedestal with the
bear in mind that the 6-way valve must
enclosed bolts (+nuts and washers) .
remain accessible .
4
Make sure that the plastic protection (funnel) is placed on top of the filter to prevent
sand/gravel from falling into the mouthpiece of the branch pipe .
6
7
After filling the filter, remove the residue
The 6-way valve is now placed on the filter and the clamp is fixed around the filter . This
of sand at the top of the filter and remove
is how the valve is connected to the filter .
the funnel .
8
9
Now apply Teflon tape to the outer thread
Unscrew the little valve at the side of the
of the manometer .
valve to fit the manometer .
54
3
Place the filter on the pedestal and fill it
with a 1/3rd water .
5
Fill the filter first with gravel (3-5mm) and then
with sand (0 . 4 -0 . 8 mm) .
The sand has an unlimited lifetime and only
need to be topped up in case sand is lost .
Mark the level of sand/gravel to be able to re-
fill the filter to the correct level at a later time .
10
The pump and filter are interlinked by a
semi-flexible tube .
Screw the connector pieces into the
filter and the pump . Slide the fittings and
11
the inserts over both ends of the hose .
Connect the fittings to the connector
pieces, and then tighten the fittings .
(see the technical section:
2 .4 .3 Connections)
2.4.3 Connections
Before you join the connectors, you
3
8
must screw the PVC elbow (7) onto
the return opening . Do this as fol-
6
lows . Screw the PVC elbow carefully
onto the return piece with some
Teflon on the thread and ensure that
5
2
this is done in one fluid movement,
without stopping or unscrewing and
with the outlet pointing downwards
at a right angle . You must then
9
tighten the ring with the proper span-
4
4
ner, while holding the return piece in
place on the inside of the pool . This
is to ensure that the return piece
remain in position .
In general, the semi-flexible con-
nector tubes need to be shortened
straight and square . Prepare the con-
nectors 1, 3, 4 and 6 as follows .
Couplings
Unscrew the nut completely from
the fitting . Slide the nut with the in-
sert over the flexible tube . Then slide
the white clamp over the tube until
approximately 2 cm of tube sticks out
below the white clamp .
Now push the tube into the fitting
up to the edge and press the white
clamp down onto the fitting . Place
the seal into the fitting .
Tighten the nut of the fitting .
This way it will be perfectly water-
proof .
If you have a coupling without a rub-
ber packing, you are advised to apply
Teflon to the thread or nipple in order
to maintain it's waterproof capacity .
Taps
Prepare the connectors to the tap in
the same way as the couplings, but
1
1
10
ENGLISH
in both directions from the tap .
Connecting the filter unit to the
pool.
Follow the drawing . Connect the 2
skimmers with the semi-flexible con-
nection tube to the T-joint (9) (glue) .
Glue to the remaining end of the
T-joint a semi-
flexible connection tube, connect
to the pump and place a ball-valve
in-between (4, 5, 6, 8, 9) . 4, 5 and 9
should have been coupled after the
placement of
the skimmers, in order to continue
filling the pool .
Then, connect the 2 water return
devices to the T-joint (10) (glue) . Glue
to the
remaining end of the T-joint a semi-
flexible connection tube, connect to
the filter and fit a ball valve to this
connection too (1, 2, 3, 10) . 1, 2 and
10 should have been coupled already
after fitting the return devices,
in order to continue filling the pool .
After installation, the filter needs
to be backwashed automatically; in
this pro-cess the filter sand is rinsed
to prevent impurities from entering
the pool .
Afterwards, you place the valve in
the filter position and let the pump
run; the needle of the manometer
indicates the nominal pressure to
which the filter is exposed . Write
down this pressure (normally be-
tween 0 .6 and 1 .1 bar) .
55
Advertenties
Hoofdstukken
Inhoudsopgave
