Mains Connection - Gude GWS 700 HM-2 Vertaling Van De Originele Gebruiksaanwijzing
Wip
Verberg thumbnails
Zie ook voor GWS 700 HM-2:
- Vertaling van de originele gebruiksaanwijzing (69 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ENGLISH
28
Residual Risk
Risk of injury!
In spite of compliance with all relevant design
regulations, dangers may still present themselves
when the machine is operated, e.g.:
• Risk of injury to fingers and hands. Never put your
hands in the saw blade area.
• Parts of workpieces and tools fly off from damaged
tools. Wear eye protectors.
• Noise emission: It is necessary to wear ear protec-
tors.
• Wood dust emission: Wear a respirator.
Despite the observance of the operating instructions
there still may be some hidden residual risks.
Residual risks may be minimised by following the
safety instructions and use as designated provisions
and the Operating Instructions.
The exposure to dust is influenced by the type of
the material processed. It is important to use local
exhaust (catching near the source) and adjust well
the exhaust covers, guide elements and the grab
channels.
Dust produced during work is often harmful and
must not get in your body. Use the exhauster and
wear an appropriate respirator, too. Remove tho-
roughly any deposited dust, e.g. by vacuuming.
Use saw blades designed to reduce emitted noise.
Keep the machine and saw blade running.
To minimise noise production, the tool must be
sharpened and all elements for noise minimisation
(covers, etc.) must be properly adjusted.
Emergency procedure
Conduct a first-aid procedure adequate to the
injury and summon qualified medical attendance
as quickly as possible. Protect the injured person
from further harm and calm them down. If you seek
help, state the following pieces of information: 1.
Accident site, 2. Accident type, 3. Number of injured
persons, 4. Injury type(s)
Mains Connection
Operation is only allowed with a safety switch
against stray current (RCD max. stray current of
30mA).
Before putting into operation, a qualified electri-
cian must check whether electric safety measures
required are in place. Any national regulations in this
regard must be complied with.
Electric connection to a socket.
It is necessary to make sure the connecting socket
was not near water and humidity and the plug was
protected against humidity.
Check the voltage. Technical data given on the type
label must correspond with electric network voltage.
Only use splash proof extension cables approved for
outdoor purposes.
Check the cable and/or socket for damages before
the appliance putting into operation. In case dama-
ge let repaired in authorized workshop
To avoid danger, a damaged mains supply pipe must
be replaced by the manufacturer. Do not under any
circumstances attempt any repair yourself.
Cable connections to be separated by pulling the
plug only. Pulling the cable could damage both the
cable and plug. As a result, electric safety would no
longer be guaranteed.
GWS 500 HM-2
Special connection criteria according to EN 61000-
3-11. The machine meets the requirements of EN
61000-3-11 and is subject to special connection crite-
ria. This means that the machine may not be used at
any arbitrary connection points.
The machine can cause temporary voltage fluctuati-
ons in poor mains supply conditions.
As the user, you must ensure (if necessary, in con-
sultation with your power supply company) that the
connection point at which you wish to operate the
machine meets the above requirements.
Symbols
CAUTION! WARNING
Caution!
Read the operating instructions to redu-
ce the risk of injury.
Caution!
Unplug the machine before any servicing
or repair!
Always wear goggles when using the
machine.
Wear ear protectors!
Wear safety shoes with steel reinforce-
ment.
Wear protective gloves
Wear dust mask.
Wear protective clothing
Advertenties
Inhoudsopgave
