Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
7.1
Attaching the grinding wheel
Move the spindle locking button (3) only when
the motor is at a standstill.
See figure, page 2.
1. Locking the spindle: Move the spindle locking
button (3) in position
(11) by hand until the spindle locking clearly
engages.
2. Placing the grinding wheel in position:
Place the grinding wheel on the support flange
(11).
The grinding wheel must lay flat on the support
flange (11) .
3. Securing the fixing screw:
Fit the fixing screw (1)and firmly tighten with
hexagon wrench (7). Remove the hexagon
wrench again and place into the wrench storage
(7).
4. Release the spindle lock:
Move the spindle lock button (3) in position
7.2
Removing the grinding disc
1. Locking the spindle: Move the spindle locking
button (3) in position
(11) by hand until the spindle locking clearly
engages.
2. Removing the fixing screw:
Remove the fixing screw (1) with hexagon
wrench (7) and remove.
3. Removing the grinding disc.
4. Release the spindle lock:
Move the spindle lock button (3) in position
8. Use
8.1
Switching on and off
Check that the spindle lock button (3) is in
position
.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off and keep it away from dust
deposits. After switching off the machine, only set it
down when the motor has come to a standstill.
Avoid switching on the machine accidentally:
always switch it off when the battery pack is
removed from the machine.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine using
the handles provided, stand in a safe position and
concentrate.
Machines with a slide switch:
4
0
Switching on: push the slide switch (4) forwards.
For continuous operation, tilt it downwards
until it engages.
and turn support flange
and turn support flange
I
Switching off: press the rear end of the slide switch
(4) and release it.
8.2
Working Directions
Grinding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Rough grinding: position the machine at an angle of
30° - 40° for the best working results.
Cut-off grinding:
Always work against the run of the disc
(see illustration). Otherwise the
machine may kick back from the cut in
an out of control manner. Guide the
machine evenly at a speed suitable for
the material being processed. Do not tilt, apply
excessive force or sway from side to side.
Sanding:
.
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.
9. Cleaning
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
.
Remove the battery pack periodically and wipe the
contact area of the battery pack and machine with a
dry cloth and remove deposits. If the battery pack
cannot be removed: see the Repairs chapter.
10. Troubleshooting
Electronic safety shutdown: the machine has
SHUT DOWN by itself. In the even of longer
blocking, the machine shuts down. Switch off the
machine. Switch it on again and continue to work as
normal. Try to prevent the machine from seizing.
See chapter 4.2.
Check that the spindle lock button (3) is in position
.
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Chargers: ASC 55, SC 30, etc.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
12 V, 2.0 Ah, Li-Power ......................... 625406000
12 V, 4.0 Ah, LiHD ............................... 625349000
18 V, 2.0 Ah, Li-Power ......................... 625596000
18 V, 4.0 Ah, LiHD ............................... 625367000
ENGLISH en
15
Advertenties
Inhoudsopgave
