Advertenties
Beschikbare talen
Beschikbare talen
(17). The wet and dry floor brush (24) is designed for industrial/commercial cleaning, as its suction power is higher. For home use,
there is a wet and dry floor brush (25), also suitable for carpet cleaning.
Function 4: Collecting ashes from the fireplace
Install a HEPA filter (12) and a fire-resistant cotton filter (20) under the main cover (7). The ash will be collected directly into the
stainless steel container (4). To do this, use a metal ash hose (18) and an aluminum ash nozzle (19).
CAUTION: Do not use this ash cleaning equipment when the ash temperature is higher than 45 ℃ or when the wood residue is still
glowing!
Function 5: Wet cleaning
Under the main cover (7), install the sponge filter (13) and construction seal (27) on the wound of the stainless steel container (4).
Wet waste will be collected directly into the stainless steel container (4). The paper bag (26) is not recommended for wet cleaning.
A wet and dry floor brush (24) and a stainless steel telescopic tube (11) with a plastic hose (17) are recommended for this function.
NOTE: The device is designed for cleaning wet mud, wet dust, wet sand. The device is not a dirty water pump for collecting large
amounts of water, for example, from a flooded basement.
Function 6: Blower
The blower helps clean up fallen leaves in the garden or helps clear dust from hard-to-reach corners. Install the blower cover (14)
on the back of the main cover (7), then attach the construction gasket (27) to the wound of the stainless steel container (4) and
insert the plastic hose (17) into the hole in the blower cover ( 14).
Synchronized tool socket - Photo D
This is an additional feature of this device useful in the construction industry, extremely valuable due to the fact that the device is
equipped with an extra-long 15-meter power cord.
The "II" position of the switch (1) is used only when another electric construction tool: for example, a wall grinder has been
connected to a vacuum cleaner. When the switch is pushed to the "II" position, the vacuum cleaner does not work. But when the
user plugs in, for example, a wall sander, the vacuum cleaner will start working in 2 seconds. If the user turns off the wall grinder,
the vacuum cleaner will continue to run for 8 seconds, allowing it to suck up the remaining dust, and after 8 seconds the device will
automatically stop working. The tool socket is designed for the vacuum cleaner and other power tools to work together. The power
of the socket is 2000W. Use a construction tool adapter (23) and a plastic hose (17) to install tools.
CLEANING AND MAINTENANCE
Before cleaning and maintenance, turn off the unit and remove the plug from the outlet.
A. Filter cleaning.
1. Wash the filters with water (max 40 ℃). When washing the HEPA filter (12) / sponge filter (13) / cotton filter (20), be gentle and
avoid brushing, as they are easy to tear.
2.Remember to dry each filter for at least 24 hours before using it again. You can contact your local retailers to buy replacements.
3. The paper bag cannot be washed. When full, remember to replace it with a new one.
B. Cleaning accessories
1. Regularly wash the hoses, telescopic tube and floor brushes to prevent debris from blocking them.
2. Shake off any remaining water inside after cleaning and make sure they dry for at least 24 hours.
C. Cleaning the tank
1. Clean the surface of the tank and its interior.
2. Remember to wipe it down!
TECHNICAL SPECIFICATIONS:
Tank capacity 25 liters
Air flow rate 36 liters / sec. / (2.16 m³ / h)
Suction power 20 kPa
Nominal power 1400W
Synchronized tool socket: 2000W
Maximum power 3400W
Power supply 220-240V ~50/60Hz
Noise level: 82 dB
Product dimensions 55 x 40 x 40 cm
8
Advertenties
