Satel VERSA Handleiding pagina 74
Verberg thumbnails
Zie ook voor VERSA:
- Installatiehandleiding (35 pagina's) ,
- Gebruikershandleiding (20 pagina's) ,
- Handleiding (13 pagina's)
Inhoudsopgave
Advertenties
72
2011-06
1.02
2012-06
1.02
2012-10
1.03
Programmeer Handleiding
• Description of "Cut-off time" output parameter has been updated (p. 39).
• Description of "Clearing from partition 1" and "Clearing from partition 2" output
options has been updated (p. 41).
• Description of "Reset in partition 1" and "Reset in partition 2" output options has
been changed (p. 41).
• Description of "Pulse" output option has been updated (p. 41).
• Description of "Arming/Disarming/Clearing signaling" output options has been
updated (p. 42).
• Description of "Mainboard TMP input" output options has been added (p. 42).
• Description of "Arm mode review" keypad option has been modified (p. 44).
• Section "ETHM-1 Ethernet module" has been added (p. 46).
• Information on AMD-102 wireless magnetic contact and its programming has been
added (pages 48, 53 and 56).
• Information on ARD-100 wireless detector and its programming has been added
(pages 48, 54 and 57).
• A note about panic devices interacting with ACU-100 controller has been added
(p. 50).
• Note about tamper alarm signaling by wireless sirens of ABAX system has been
modified (p. 51).
• A note about programming sensitivity of zones in wireless expanders of hard-
wired zones and outputs has been added (p. 51).
• Information on reporting events via Ethernet network after connection of ETHM-1
module has been added to section "Reporting" (p. 61).
• Section "Reporting via Ethernet network" has been added (p. 65).
• Description of "Zone inhibition" and "Zone isolation" rights has been added (p. 68).
• Description of "Inspection" user right has been updated (p. 68).
• Description of "DURESS" right has been supplemented (p. 69).
• Section "Confirmation on LEDs in APT-100 keyfob" has been added (p. 70).
• Section "Compliance with EN 50131 Standard Requirements for Grade 2" has
been added (p. 71).
• Some figures have been replaced (e.g. because of changing the D
appearance).
• Description of "Answering/remote control when armed partition 1 / 2" global
options has been added (p. 26).
• Description of "20. Alarm/arm status" output function has been added (p. 39).
• Description of "21. Detectors resetting" output function has been added (p. 39).
• Section "Output parameters" has been updated (p. 39).
• Section "Output options" has been updated (p. 41).
• In section "Messaging parameters and options" the description of "Code" and
"User" parameters has been added (p. 66).
• Description of "Zone isolation" right has been modified (p. 68).
• Description of "INT-VG access" right has been added (p. 69).
• In connection with new keypads being put on the market, the information on
keypads contained in manual has been modified.
• Service mode menu has been updated (p. 7-12).
• Information on wireless zones has been modified (p. 29 and 30).
• Description of "Higher sensitivity for jamming detection" option has been added
(p. 47).
• Description of test mode in ABAX system has been modified (p. 47).
• Description of additional programmable parameters and options for ABAX wireless
devices has been modified (p. 48).
• Section "433 MHz wireless system controller" has been added (p. 58).
SATEL
X program
LOAD
Advertenties
Inhoudsopgave
